Otwarty dostęp

Numerical Modeling of Wall Pressure in Silo with and Without Insert

Frzat Askif

Frzat Askif

Faculty of Civil Engineering, International University for Science and TechnologyDamascus, Syria
Wyszukaj tego autora
Sciendo|Google Scholar
Askif, Frzat
, 
Hala Hammadeh

Hala Hammadeh

Faculty of Engineering, Middle East UniversityAmman, Jordan
Wyszukaj tego autora
Sciendo|Google Scholar
Hammadeh, Hala
, 
Andrzej Ubysz

Andrzej Ubysz

Faculty of Civil Engineering, Wroclaw University of Science and TechnologyWroclaw, Poland
Wyszukaj tego autora
Sciendo|Google Scholar
Ubysz, Andrzej
 oraz 
Marek Maj

Marek Maj

Faculty of Civil Engineering, Wroclaw University of Science and TechnologyWroclaw, Poland
Wyszukaj tego autora
Sciendo|Google Scholar
Maj, Marek
  
28 paź 2020
Numerical Modeling of Wall Pressure in Silo with and Without Insert's Cover Image
O artykule
Poprzedni artykuł
Następny artykuł
Zacytuj
Pobierz okładkę
Kategoria artykułu: Original Study
Data publikacji: 28 paź 2020
Zakres stron: 22 - 33
Otrzymano: 18 lip 2020
Przyjęty: 21 wrz 2020
DOI: https://doi.org/10.2478/sgem-2020-0009
Słowa kluczowe
© 2021 Frzat Askif et al., published by Sciendo
This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Figure 1

The used model in the experiments.
The used model in the experiments.

Figure 2

The measuring cell levels.
The measuring cell levels.

Figure 3

The used insert inside the model.
The used insert inside the model.

Figure 4

The used insert.
The used insert.

Figure 5

Corn used in the experiment.
Corn used in the experiment.

Figure 6

Measuring cell used in the experiment.
Measuring cell used in the experiment.

Figure 7

Dynamic horizontal pressure distribution that resulted on the silo wall without insert (no insert used)/
Dynamic horizontal pressure distribution that resulted on the silo wall without insert (no insert used)/

Figure 8

Dynamic horizontal pressure distribution that resulted on the silo wall with insert.
Dynamic horizontal pressure distribution that resulted on the silo wall with insert.

Figure 9

Stress deformation scheme for steel (current study)
Stress deformation scheme for steel (current study)

Figure 10

The CAX4R element (Abaqus V6.12-1).
The CAX4R element (Abaqus V6.12-1).

Figure 11

Mechanical transmission of forces in contact surfaces
Mechanical transmission of forces in contact surfaces

Figure 12

Contact Pair surface.
Contact Pair surface.

Figure 13

Peripheral conditions applied to the numerical model: (a) without an input element and (b) with an input element.
Peripheral conditions applied to the numerical model: (a) without an input element and (b) with an input element.

Figure 14

Adaptive grid Lagrangian–Eulerian – ALE (Abaqus V6.12-1).
Adaptive grid Lagrangian–Eulerian – ALE (Abaqus V6.12-1).

Figure 15

Definition of ALE field on the numerical model (current study).
Definition of ALE field on the numerical model (current study).

Figure 16

Silo model without insert (Abaqus)
Silo model without insert (Abaqus)

Figure 17

Time-adaptive grid distortion for the case without the use of insert (Abaqus).
Time-adaptive grid distortion for the case without the use of insert (Abaqus).

Figure 18

The comparison is between the pressure produced by the numerical study and the pressure produced by the experimental study without the use of an insert.
The comparison is between the pressure produced by the numerical study and the pressure produced by the experimental study without the use of an insert.

Figure 19

Silo model with insert.
Silo model with insert.

Figure 20

Adaptive grid deformation over time of flow state without the use of insert.
Adaptive grid deformation over time of flow state without the use of insert.

Figure 21

The comparison is between the pressure produced by the numerical study and the pressure registered by the experimental study with insert.
The comparison is between the pressure produced by the numerical study and the pressure registered by the experimental study with insert.
Język:
Angielski
Częstotliwość wydawania:
4 razy w roku
Dziedziny czasopisma:
Nauki o Ziemi, Nauki o Ziemi, inne, Nauka o materiałach, Kompozyty, Materiały porowate, Fizyka, Mechanika i dynamika płynów
Kanał RSS czasopisma