Login
Registrieren
Passwort zurücksetzen
Veröffentlichen & Verteilen
Verlagslösungen
Vertriebslösungen
Themen
Allgemein
Altertumswissenschaften
Architektur und Design
Bibliotheks- und Informationswissenschaft, Buchwissenschaft
Biologie
Chemie
Geowissenschaften
Geschichte
Industrielle Chemie
Informatik
Jüdische Studien
Kulturwissenschaften
Kunst
Linguistik und Semiotik
Literaturwissenschaft
Materialwissenschaft
Mathematik
Medizin
Musik
Pharmazie
Philosophie
Physik
Rechtswissenschaften
Sozialwissenschaften
Sport und Freizeit
Technik
Theologie und Religion
Wirtschaftswissenschaften
Veröffentlichungen
Zeitschriften
Bücher
Konferenzberichte
Verlage
Blog
Kontakt
Suche
EUR
USD
GBP
Deutsch
English
Deutsch
Polski
Español
Français
Italiano
Warenkorb
Home
Zeitschriften
Studia Geotechnica et Mechanica
Band 43 (2021): Heft 1 (April 2021)
Uneingeschränkter Zugang
Numerical Modeling of Wall Pressure in Silo with and Without Insert
Frzat Askif
Frzat Askif
,
Hala Hammadeh
Hala Hammadeh
,
Andrzej Ubysz
Andrzej Ubysz
und
Marek Maj
Marek Maj
| 28. Okt. 2020
Studia Geotechnica et Mechanica
Band 43 (2021): Heft 1 (April 2021)
Über diesen Artikel
Vorheriger Artikel
Nächster Artikel
Zusammenfassung
Artikel
Figuren und Tabellen
Referenzen
Autoren
Artikel in dieser Ausgabe
Vorschau
PDF
Zitieren
Teilen
Article Category:
Original Study
Online veröffentlicht:
28. Okt. 2020
Seitenbereich:
22 - 33
Eingereicht:
18. Juli 2020
Akzeptiert:
21. Sept. 2020
DOI:
https://doi.org/10.2478/sgem-2020-0009
Schlüsselwörter
Numerical modeling
,
silo
,
silo model
,
flow pressure
,
insert
,
wall pressure
© 2021 Frzat Askif et al., published by Sciendo
This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Figure 1
The used model in the experiments.
Figure 2
The measuring cell levels.
Figure 3
The used insert inside the model.
Figure 4
The used insert.
Figure 5
Corn used in the experiment.
Figure 6
Measuring cell used in the experiment.
Figure 7
Dynamic horizontal pressure distribution that resulted on the silo wall without insert (no insert used)/
Figure 8
Dynamic horizontal pressure distribution that resulted on the silo wall with insert.
Figure 9
Stress deformation scheme for steel (current study)
Figure 10
The CAX4R element (Abaqus V6.12-1).
Figure 11
Mechanical transmission of forces in contact surfaces
Figure 12
Contact Pair surface.
Figure 13
Peripheral conditions applied to the numerical model: (a) without an input element and (b) with an input element.
Figure 14
Adaptive grid Lagrangian–Eulerian – ALE (Abaqus V6.12-1).
Figure 15
Definition of ALE field on the numerical model (current study).
Figure 16
Silo model without insert (Abaqus)
Figure 17
Time-adaptive grid distortion for the case without the use of insert (Abaqus).
Figure 18
The comparison is between the pressure produced by the numerical study and the pressure produced by the experimental study without the use of an insert.
Figure 19
Silo model with insert.
Figure 20
Adaptive grid deformation over time of flow state without the use of insert.
Figure 21
The comparison is between the pressure produced by the numerical study and the pressure registered by the experimental study with insert.