Connexion
S'inscrire
Réinitialiser le mot de passe
Publier & Distribuer
Solutions d'édition
Solutions de distribution
Thèmes
Architecture et design
Arts
Business et économie
Chimie
Chimie industrielle
Droit
Géosciences
Histoire
Informatique
Ingénierie
Intérêt général
Linguistique et sémiotique
Littérature
Mathématiques
Musique
Médecine
Pharmacie
Philosophie
Physique
Sciences bibliothécaires et de l'information, études du livre
Sciences des matériaux
Sciences du vivant
Sciences sociales
Sport et loisirs
Théologie et religion
Études classiques et du Proche-Orient ancient
Études culturelles
Études juives
Publications
Journaux
Livres
Comptes-rendus
Éditeurs
Blog
Contact
Chercher
EUR
USD
GBP
Français
English
Deutsch
Polski
Español
Français
Italiano
Panier
Home
Journaux
Materials Science-Poland
Édition 35 (2017): Edition 1 (March 2017)
Accès libre
Effect of target power on the physical properties of Ti thin films prepared by DC magnetron sputtering with supported discharge
A. Kavitha
A. Kavitha
,
R. Kannan
R. Kannan
et
S. Rajashabala
S. Rajashabala
| 24 févr. 2017
Materials Science-Poland
Édition 35 (2017): Edition 1 (March 2017)
À propos de cet article
Article précédent
Article suivant
Résumé
Article
Figures et tableaux
Références
Auteurs
Articles dans cette édition
Aperçu
PDF
Citez
Partagez
Publié en ligne:
24 févr. 2017
Pages:
173 - 180
Reçu:
05 juil. 2016
Accepté:
05 janv. 2017
DOI:
https://doi.org/10.1515/msp-2017-0022
Mots clés
Ti thin films
,
supported discharge/triode mode
,
DC magnetron sputtering
,
target power
© 2017 A. Kavitha, R. Kannan, S. Rajashabala
This article is distributed under the terms of the Creative Commons Attribution Non-Commercial License, which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.
(a) schematic diagram of DC magnetron sputtering with supported discharge, (b) electrical circuit diagram of the supported discharge.
Voltage-current characteristics in diode mode and triode mode at different filament bias currents.
Variation of target current with target voltage at a constant filament bias current of 1.0 A for different pressures.
Variation of thickness/rate of deposition on target power for the films deposited in diode and supported discharge modes, for dS−T = 4 cm.
EDS spectra for the Ti thin films deposited at (a) 3 Pa and (b) 0.7 Pa.
XRD patterns of Ti thin films deposited at a pressure of (a) 3 Pa, (b) 0.7 Pa at different target powers.
SEM images of Ti thin films deposited in diode mode at the target power of (a) 60 W, (b) 80 W, (c) 100 W and (d) 120 W.
Ti thin films deposited in triode mode at the target power of (a) 60 W, (b) 80 W, (c) 100 W and (d) 120 W.
AFM images of Ti films deposited in supported discharge system at the target power of (a) 60W, (b) 80 W, (c) 100 W and (d) 120 W.
Variation of electrical resistivity with target power of Ti thin films deposited in diode and triode mode.
Qualitative analysis of crystallite size.
Working pressure [Pa]
Target power [W]
Grain size [nm]
Relative intensity [%]
Surface roughness [nm]
80
64
36
7
0.7
100
65
62
12
120
80
100
15
80
12
8
2
3
100
13
9
4
120
20
12
5