Logowanie
Zarejestruj się
Zresetuj hasło
Publikuj i Dystrybuuj
Rozwiązania Wydawnicze
Rozwiązania Dystrybucyjne
Dziedziny
Architektura i projektowanie
Bibliotekoznawstwo i bibliologia
Biznes i ekonomia
Chemia
Chemia przemysłowa
Filozofia
Fizyka
Historia
Informatyka
Inżynieria
Inżynieria materiałowa
Językoznawstwo i semiotyka
Kulturoznawstwo
Literatura
Matematyka
Medycyna
Muzyka
Nauki farmaceutyczne
Nauki klasyczne i starożytne studia bliskowschodnie
Nauki o Ziemi
Nauki o organizmach żywych
Nauki społeczne
Prawo
Sport i rekreacja
Studia judaistyczne
Sztuka
Teologia i religia
Zagadnienia ogólne
Publikacje
Czasopisma
Książki
Materiały konferencyjne
Wydawcy
Blog
Kontakt
Wyszukiwanie
EUR
USD
GBP
Polski
English
Deutsch
Polski
Español
Français
Italiano
Koszyk
Home
Czasopisma
Journal of Electrical Bioimpedance
Tom 6 (2015): Zeszyt 1 (January 2015)
Otwarty dostęp
Parallel, multi frequency EIT measurement, suitable for recording impedance changes during epilepsy
T. Dowrick
T. Dowrick
,
G. Sato Dos Santos
G. Sato Dos Santos
,
A. Vongerichten
A. Vongerichten
oraz
D. Holder
D. Holder
| 21 gru 2015
Journal of Electrical Bioimpedance
Tom 6 (2015): Zeszyt 1 (January 2015)
O artykule
Poprzedni artykuł
Następny artykuł
Abstrakt
Artykuł
Ilustracje i tabele
Referencje
Autorzy
Artykuły w tym zeszycie
Podgląd
PDF
Zacytuj
Udostępnij
Article Category:
Articles
Data publikacji:
21 gru 2015
Zakres stron:
37 - 43
Otrzymano:
02 gru 2015
DOI:
https://doi.org/10.5617/jeb.2573
Słowa kluczowe
Electrical Impedance Tomography (EIT)
,
Biomedical Circuits
,
Epilepsy
© 2015 T. Dowrick, G. Sato Dos Santos, A. Vongerichten and D. Holder, published by Sciendo
This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.
Fig. 1
A - Current source implementation. Sine wave generation performed by Arduino Nano with output filtering. Howland current pump used for V-I conversion. B – Example connection of multiple current sources to phantom.
Fig. 2
Output impedance of current source. Measured using HP43284A Impedance Analyser.
Fig. 3
Stability of current source over time, measured on a resistor phantom. The slight drift over time is thought be caused by device heating.
Fig. 4
Results of imaging test. Blue areas represent an increase in impedance. The first column indicates the position of the perturbation in the tank. The remaining columns show the reconstructed images for each frequency group used. Colour bar indicates percentage change in impedance.
Fig 5
Results of coin drop experiment. 10 frames are shown, taken 10 ms apart, for each coin dropped. Each frame uses 1 ms of recorded data. The black circle at 0 ms indicates the position at which the coin was dropped.
Fig. 6
(A) Experimental Setup. 60 electrodes were placed on either side of the brain. Seizures were triggered using a 4-AP Model. (B) Data extraction. By low pass (EEG) and bandpass (EIT) filtering, the data was split into the EEG component and the EIT component, from which the impedance change was extracted.
Fig. 7
dZ values recorded at 2.2 kHz and 2.6 kHz during a single seizure. Seizure onset is at t = 0 . Right and left refers to the site of electrode placement.
Fig. 8
Example of raw recorded data, recorded from the right hemisphere. Solid colours represent the EEG data. dZ values, from 2.2 kHz injection, are plotted on top of each channel in grey.
List of frequency groups
Group A
1800 Hz
1900 Hz
2000 Hz
2100 Hz
Group B
1980 Hz
1990 Hz
2000 Hz
2010 Hz
Group C
1998 Hz
1999 Hz
2000 Hz
2001 Hz