Logowanie
Zarejestruj się
Zresetuj hasło
Publikuj i Dystrybuuj
Rozwiązania Wydawnicze
Rozwiązania Dystrybucyjne
Dziedziny
Architektura i projektowanie
Bibliotekoznawstwo i bibliologia
Biznes i ekonomia
Chemia
Chemia przemysłowa
Filozofia
Fizyka
Historia
Informatyka
Inżynieria
Inżynieria materiałowa
Językoznawstwo i semiotyka
Kulturoznawstwo
Literatura
Matematyka
Medycyna
Muzyka
Nauki farmaceutyczne
Nauki klasyczne i starożytne studia bliskowschodnie
Nauki o Ziemi
Nauki o organizmach żywych
Nauki społeczne
Prawo
Sport i rekreacja
Studia judaistyczne
Sztuka
Teologia i religia
Zagadnienia ogólne
Publikacje
Czasopisma
Książki
Materiały konferencyjne
Wydawcy
Blog
Kontakt
Wyszukiwanie
EUR
USD
GBP
Polski
English
Deutsch
Polski
Español
Français
Italiano
Koszyk
Home
Czasopisma
Studia Geotechnica et Mechanica
Tom 44 (2022): Zeszyt 1 (March 2022)
Otwarty dostęp
Importance of seismic wave frequency in FEM-based dynamic stress and displacement calculations of the earth slope
Krzysztof Fuławka
Krzysztof Fuławka
,
Anna Kwietniak
Anna Kwietniak
,
Vera Lay
Vera Lay
oraz
Izabela Jaśkiewicz-Proć
Izabela Jaśkiewicz-Proć
| 09 lut 2022
Studia Geotechnica et Mechanica
Tom 44 (2022): Zeszyt 1 (March 2022)
O artykule
Poprzedni artykuł
Następny artykuł
Abstrakt
Artykuł
Ilustracje i tabele
Referencje
Autorzy
Artykuły w tym zeszycie
Podgląd
PDF
Zacytuj
Udostępnij
Article Category:
Original Study
Data publikacji:
09 lut 2022
Zakres stron:
82 - 96
Otrzymano:
22 cze 2021
Przyjęty:
16 gru 2021
DOI:
https://doi.org/10.2478/sgem-2022-0002
Słowa kluczowe
Slope stability
,
Numerical analysis
,
Seismic load
,
Frequency analysis
© 2022 Krzysztof Fuławka et al., published by Sciendo
This work is licensed under the Creative Commons Attribution 4.0 International License.
Figure 1
Comparison of spectrograms for mining-induced high-energy tremors with energy of 1.9 × 109 J (left) and 1.2 × 107 J (right).
Figure 2
The dominant frequency content of LGCB mining-induced tremors in relation to their epicentral distance and energy (over 430 entries, vertical and horizontal components were studied).
Figure 3
The spectral amplitude characteristic of harmonic signals used in FEM dynamic analysis.
Figure 4
Geometry of slope used for numerical simulation.
Figure 5
Maximum element size in the dynamic model according to Kuhlemeyer and Lysmer law (blue line) and element size used for the purposes of this analysis (red bars).
Figure 6
Analysed variants of seismic load direction.
Figure 7
Matrix of numerical scenarios used for the presented research.
Figure 8
The calculated absolute values of displacement (top) and shear stress (down) changes at the base of the analysed slope depending on the used frequency.
Figure 9
The maximum calculated value of total displacement (top) and shear stress (bottom) at the base of the slope for all 180 cases.
Figure 10
The RSM surface map of the relation between dominant frequency, slope angle and displacement (left) and shear stress (right) for scenarios in which the direction of seismic load is the same as the direction of slope failure.
Figure 11
The RSM surface map of the relation between dominant frequency, slope angle and displacement (left) and shear stress (right) for scenarios in which the direction of seismic load is opposite to the direction of slope failure.
Material parameters used for numerical simulation.
Parameter
Unit weight
Young modulus
Poisson ratio
Tensile strength
Cohesion
Friction angle
Dilation angle
Unit
kN/m
3
kPa
-
kPa
kPa
°
°
Value
19
100,000
0.4
5
5
38
0