Logowanie
Zarejestruj się
Zresetuj hasło
Publikuj i Dystrybuuj
Rozwiązania Wydawnicze
Rozwiązania Dystrybucyjne
Dziedziny
Architektura i projektowanie
Bibliotekoznawstwo i bibliologia
Biznes i ekonomia
Chemia
Chemia przemysłowa
Filozofia
Fizyka
Historia
Informatyka
Inżynieria
Inżynieria materiałowa
Językoznawstwo i semiotyka
Kulturoznawstwo
Literatura
Matematyka
Medycyna
Muzyka
Nauki farmaceutyczne
Nauki klasyczne i starożytne studia bliskowschodnie
Nauki o Ziemi
Nauki o organizmach żywych
Nauki społeczne
Prawo
Sport i rekreacja
Studia judaistyczne
Sztuka
Teologia i religia
Zagadnienia ogólne
Publikacje
Czasopisma
Książki
Materiały konferencyjne
Wydawcy
Blog
Kontakt
Wyszukiwanie
EUR
USD
GBP
Polski
English
Deutsch
Polski
Español
Français
Italiano
Koszyk
Home
Czasopisma
Journal of Electrical Bioimpedance
Tom 13 (2022): Zeszyt 1 (January 2022)
Otwarty dostęp
Diabetic foot assessment using skin impedance in a custom made sensor-sock
Christian Tronstad
Christian Tronstad
,
Maryam Amini
Maryam Amini
,
Eline Olesen
Eline Olesen
,
Elisabeth Qvigstad
Elisabeth Qvigstad
,
Oliver Pabst
Oliver Pabst
,
Tormod Martinsen
Tormod Martinsen
,
Sisay M. Abie
Sisay M. Abie
,
Ørjan G. Martinsen
Ørjan G. Martinsen
,
Jonny Hisdal
Jonny Hisdal
,
Trond G. Jenssen
Trond G. Jenssen
oraz
Håvard Kalvøy
Håvard Kalvøy
| 14 sty 2023
Journal of Electrical Bioimpedance
Tom 13 (2022): Zeszyt 1 (January 2022)
O artykule
Poprzedni artykuł
Następny artykuł
Abstrakt
Artykuł
Ilustracje i tabele
Referencje
Autorzy
Artykuły w tym zeszycie
Podgląd
PDF
Zacytuj
Udostępnij
Data publikacji:
14 sty 2023
Zakres stron:
136 - 142
Otrzymano:
07 gru 2022
DOI:
https://doi.org/10.2478/joeb-2022-0019
Słowa kluczowe
Skin impedance
,
diabetes
,
diabetic foot
,
neuropathy
© 2022 Christian Tronstad, Maryam Amini, Eline Olesen, Elisabeth Qvigstad , Oliver Pabst, Tormod Martinsen, Sisay M. Abie, Ørjan G. Martinsen, Jonny Hisdal, Trond G. Jenssen, Håvard Kalvøy, published by Sciendo
This work is licensed under the Creative Commons Attribution 4.0 International License.
Figure 1
Screenshot from Eagle CAD design showing the electrode geometry (each grid unit is 1mm).
Figure 2
Axisymmetric 2D distribution of simulated volume impedance density below the electrode for low (a) and high (b) frequency impedance measurement. The color gradient indicates the volume impedance density, presented on a logarithmic scale.
Figure 3
CAD design of sensor parts for skin impedance measurement at the big toe (A), toeball (B) and heel (C). The 3D printed parts for sensor housing are shown in D, and all parts connected to the foot are shown in E.
Figure 4
An example measurement of change in measured skin impedance over 30 minutes using the electrode probe at the big toe pulp of a healthy subject. These measurements were done with the Solartron 1260+1294.
Figure 5
Impedance spectra presented as the impedance modulus (|Z|), resistance (R) and reactance (X) for all participants from the control (black) and DPN group (blue). The bumpy curves with the highest impedance in the toeball and heel plots curves are affected by measurement error due to the high impedance levels and do not represent a true frequency-dependency of the skin impedance.
Figure 6
Comparison of the repeatability of all measurements (control and DPN groups combined) between the different skin sites presented in a boxplot with group means added in grey dots. White dots represent outliers and edges of the whiskers represent the minimum and maximum non-outlier values within the groups. Repeatability was calculated using the log10-transformed impedance modulus at 10 Hz, taking the standard deviation of the successive measurements divided by the mean.