Logowanie
Zarejestruj się
Zresetuj hasło
Publikuj i Dystrybuuj
Rozwiązania Wydawnicze
Rozwiązania Dystrybucyjne
Dziedziny
Architektura i projektowanie
Bibliotekoznawstwo i bibliologia
Biznes i ekonomia
Chemia
Chemia przemysłowa
Filozofia
Fizyka
Historia
Informatyka
Inżynieria
Inżynieria materiałowa
Językoznawstwo i semiotyka
Kulturoznawstwo
Literatura
Matematyka
Medycyna
Muzyka
Nauki farmaceutyczne
Nauki klasyczne i starożytne studia bliskowschodnie
Nauki o Ziemi
Nauki o organizmach żywych
Nauki społeczne
Prawo
Sport i rekreacja
Studia judaistyczne
Sztuka
Teologia i religia
Zagadnienia ogólne
Publikacje
Czasopisma
Książki
Materiały konferencyjne
Wydawcy
Blog
Kontakt
Wyszukiwanie
EUR
USD
GBP
Polski
English
Deutsch
Polski
Español
Français
Italiano
Koszyk
Home
Czasopisma
Studia Geotechnica et Mechanica
Tom 45 (2023): Zeszyt s1 (December 2023)
Otwarty dostęp
Quality requirements for static liquefaction test of soil in triaxial apparatus
Mirosław J. Lipiński
Mirosław J. Lipiński
,
Małgorzata Wdowska
Małgorzata Wdowska
oraz
Intan Puspitaningrum
Intan Puspitaningrum
| 18 paź 2023
Studia Geotechnica et Mechanica
Tom 45 (2023): Zeszyt s1 (December 2023)
Special Issue 19th KKMGiIG
O artykule
Poprzedni artykuł
Następny artykuł
Abstrakt
Artykuł
Ilustracje i tabele
Referencje
Autorzy
Artykuły w tym zeszycie
Podgląd
PDF
Zacytuj
Udostępnij
Article Category:
Special Issue 19th KKMGiIG
Data publikacji:
18 paź 2023
Zakres stron:
395 - 404
Otrzymano:
13 mar 2023
Przyjęty:
15 wrz 2023
DOI:
https://doi.org/10.2478/sgem-2023-0019
Słowa kluczowe
static liquefaction of soil
,
triaxial test procedure
,
quality requirements
© 2023 Mirosław J. Lipiński et al., published by Sciendo
This work is licensed under the Creative Commons Attribution 4.0 International License.
Figure 1:
Types of undrained response of soil to monotonic loading: a) strain hardening (SH), b) strain softening (SS), c) limited strain softening (LSS).
Figure 2:
Sensitivity of undrained response of coarse sand to change of void ratio value: a) stress–strain characteristics, b) effective stress paths.
Figure 3:
Specimen preparation procedure for reconstitution of soil specimen for liquefaction test in a triaxial apparatus: a) moist tamping, b) dry deposition, c) water sedimentation.
Figure 4:
Position of compressibility curves of materials prepared by various specimen preparation methods.
Figure 5:
Necessary quality enhancement of test procedure for static liquefaction test.
Figure 6:
Influence of membrane penetration on a position of steady state of coarse sand (Lipiński, 2000).
Figure 7:
Specimen volume change during preparatory stages in triaxial apparatus for materials with various amount of fines (Lipiński, 2000).
Figure 8:
Change of void ratio during the first flushing with water against the initial value of the parameter (Lipinski, 2000).
Figure 9:
Reduction of friction on the top and bottom platens of triaxial apparatus (Lipinski & Wdowska, 2004).
Figure 10:
Significance of data acquisition system velocity in reconstruction of stress–strain curve in load controlled test: a) data acquired every second, b) data acquired every 20 ms.