<abstract xmlns="http://www.w3.org/1999/xhtml">

<p>The present article describes a method for enhanced accuracy in machining free-form surfaces produced on CNC milling machines. In this method, surface patch machining programs are generated based on their nominal CAD model. After the pretreatment, coordinate control measurements are carried out. The obtained results of the measurements contain information on the values and distribution of observed machining deviations. These data, after appropriate processing, are used to build a corrected CAD model of the surface produced. This model, made using reverse engineering techniques, compensates for the observed machining deviations. After regeneration of machining programs, the object processing and control measurements are repeated. As a result of the conducted procedure, the accuracy of the manufacture of the surface object is increased. This article also proposes the introduction of a simple procedure for the filtration of measurement data. Its purpose is to minimise the effect of random phenomena on the final machining error correction. The final part of the article presents the effects of the proposed method of increasing the accuracy of manufacturing on ‘raw’ and filtered measurement data. In both cases, a significant improvement in the accuracy of the machining process was achieved, with better final results obtained from the filtered measurement data. The method proposed in the article has been verified for three-axis machining with a ball-end cutter.</p>
</abstract>

The present article describes a method for enhanced accuracy in machining free-form surfaces produced on CNC milling machines. In this method, surface patch machining programs are generated based on their nominal CAD model. After the pretreatment, coordinate control measurements are carried out. The obtained results of the measurements contain information on the values and distribution of observed machining deviations. These data, after appropriate processing, are used to build a corrected CAD model of the surface produced. This model, made using reverse engineering techniques, compensates for the observed machining deviations. After regeneration of machining programs, the object processing and control measurements are repeated. As a result of the conducted procedure, the accuracy of the manufacture of the surface object is increased. This article also proposes the introduction of a simple procedure for the filtration of measurement data. Its purpose is to minimise the effect of random phenomena on the final machining error correction. The final part of the article presents the effects of the proposed method of increasing the accuracy of manufacturing on ‘raw’ and filtered measurement data. In both cases, a significant improvement in the accuracy of the machining process was achieved, with better final results obtained from the filtered measurement data. The method proposed in the article has been verified for three-axis machining with a ball-end cutter.

Method for Enhanced Accuracy in Machining Free-Form Surfaces on CNC Milling Machines

Acta Mechanica et Automatica

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

The present article describes a method for enhanced accuracy in machining free-form surfaces produced on CNC milling machines. In this method, surface patch...

Method for Enhanced Accuracy in Machining Free-Form Surfaces on CNC Milling Machines

Data publikacji: 16 mar 2022

Zakres stron: 103 - 110

Otrzymano: 29 paź 2021

Przyjęty: 22 sty 2022

DOI: https://doi.org/10.2478/ama-2022-0013

Słowa kluczowe
free-form surface, milling, coordinate measurements, CAD model, data filtration, accuracy improvement

© 2022 Andrzej Werner, published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Method for Enhanced Accuracy in Machining Free-Form Surfaces on CNC Milling Machines

Data publikacji: 16 mar 2022

Zakres stron: 103 - 110

Otrzymano: 29 paź 2021

Przyjęty: 22 sty 2022

DOI: https://doi.org/10.2478/ama-2022-0013

Słowa kluczowefree-form surface, milling, coordinate measurements, CAD model, data filtration, accuracy improvement

© 2022 Andrzej Werner, published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Słowa kluczowe
free-form surface, milling, coordinate measurements, CAD model, data filtration, accuracy improvement