<abstract xmlns="http://www.w3.org/1999/xhtml"> The subject discussed in this paper is based on an experimental bridge model which was built to study the pre-critical and post-critical buckling behaviour of steel webs of box girders provided with longitudinal and transversal stiffeners. The article presents a comparison between the experimental results and the numerical ones for buckling resistance of stiffened steel webs. For this purpose two types of analysis will be carried out: an analysis to establish the values and eigenvectors of buckling, after which the critical factor for the first mode of buckling will be obtained, and then a geometrical and physical nonlinear analysis will be performed.</abstract>

Comparative Study for Buckling Resistance of Steel Sheets Provided with Stiffeners Used in Bridge Structures

<abstract xmlns="http://www.w3.org/1999/xhtml"> This paper presents two simplified analytical methods to analyze lock gates submitted to two different accidental loads. The case of an impact involving a vessel is first investigated. In this situation, the resistance of the struck gate is evaluated by assuming a local and a global deforming mode. The super-element method is used in the first case, while an equivalent beam model is simultaneously introduced to capture the overall bending motion of the structure. The second accidental load considered in this paper is the seismic action, for which an analytical method is presented to evaluate the total hydrodynamic pressure applied on a lock gate during an earthquake, due account being taken of the fluid-structure interaction. For each of these two actions, numerical validations are presented and the analytical results are compared to finite-element solutions.</abstract>

Research Engineer, PhD, University of Liège, Faculty of Applied Sciences, ANAST Department

PhD Student, University of Liège, Faculty of Applied Sciences, ANAST Department

Professor, University of Liège, Faculty of Applied Sciences, ANAST Department

Simplified Analytical Methods to Analyze Lock Gates Submitted to Ship Collisions and Earthquakes

<abstract xmlns="http://www.w3.org/1999/xhtml"> The paper presents the results of a numerical program that was used to investigate the seismic performance of dual steel frames with dissipative shear walls. Nonlinear static and dynamic analyses were employed in order to evaluate the global ductility and the q factor for a twelve story building. The influence of the q factor on the estimated level of damage and post-earthquake intervention strategy was investigated. The dynamic analyses were conducted using two groups of accelerograms, selected to match the response spectra of two types of grounds. The numerical models were validated against experimental tests. The results show that q factor values adopted in design influence the level of damage. If re-centering capacity is properly controlled by design, the replacement of damaged walls can minimize the time and cost of intervention, thus supporting disaster resilience of buildings</abstract>

Assistant Professor, PhD, Politehnica University Timisoara, CMMC Department

Professor, PhD, Politehnica University Timisoara, CMMC Department, Romanian Academy, Timisoara Branch, CCTFA Research Center

Professor, PhD, Member of the Romanian Academy, Politehnica University Timisoara, CMMC Department, Romanian Academy, Timisoara Branch, CCTFA Research Center

Global Ductility of Dual Steel Frames with Replaceable Dissipative Shear Walls

<abstract xmlns="http://www.w3.org/1999/xhtml"> To obtain the coordinates by means of precise point positioning (PPP) technique we need to use the undifferenced GPS pseudocode and carrier phase observations but to obtain the “precise” positioning we need precise orbit and clock data too. This products and other information for obtaining the results by using PPP technique on a centimeter level accuracy can be downloaded from different locations, but the most reliable satellite ephemerides and clock correction are available from International GNSS Service (IGS).In the PPP analysis we determined the parameters such as the receiver clock error, ionospheric delays code biases, code multipath and the total neutral atmosphere delay of the observations. For the determination of the permanent station coordinates, using the PPP technique, we used precise orbit and clock solutions to enable absolute positioning of a single receiver.In this article we present the results obtained by using the PPP technique on the permanent station Oradea, from which we can conclude that the PPP technique can be used for different GNSS application.</abstract>

lecturer Ph.D. eng. – University of Oradea

Analysis of GNSS Data Using Precise Point Positioning Technique for the Determination of Permanent Station in Romania

<abstract xmlns="http://www.w3.org/1999/xhtml"> Seismic vulnerability for a structure represents the susceptibility to be affected by an event with a given intensity. The vulnerability of a structure can be influenced by the design methods or by different problems that may appear during the execution process.This paper shows a case study for the vulnerability increase of a reinforced concrete frame structure in 2 different situations:a) modification produced due to code changes, meaning P100-2006 respectively P100-2013;b) modifications produced the structure taking into account the errors which have occurred during the execution process;For both cases, capacity curves were plotted considering the nonlinear analysis, also called pushover. The numerical simulation was performed in SAP2000 software. These curves were compared with the response spectrum corresponding to the site conditions in order to obtain the performance point. For accurate results, fragility curves were plotted for both considered situations, according to previous research of the authors.The paper emphasizes the importance of each stage during the execution of a structure. More over the differences in the vulnerability index show the importance on the overall behavior of the structure. Solution to increase strength and safety for the structure are also given at the end of the paper</abstract>

Lecturer, PhD, Gheorghe Asachi Technical University of Iasi, Faculty of Civil Engineering and Building Services

PhD., eng., INICAD DESIGN S.R.L., Bucuresti

Professor, PhD, “Gh. Asachi” Technical University of Iasi, Faculty of Civil Engineering and Building Services

Case Study on Vulnerability Increase for a Reinforced Concrete Frame Structure

AHEAD OF PRINT

Volume 17 (2022): Issue 2 (June 2022)

Volume 17 (2022): Issue 1 (March 2022)

Volume 16 (2021): Issue 4 (December 2021)

Volume 16 (2021): Issue 3 (September 2021)

Volume 16 (2021): Issue 2 (June 2021)

Volume 16 (2021): Issue 1 (March 2021)

Volume 15 (2019): Issue 4 (December 2019)

Volume 15 (2019): Issue 3 (September 2019)

Volume 15 (2019): Issue 2 (June 2019)

Volume 15 (2019): Issue 1 (March 2019)

Volume 14 (2018): Issue 4 (December 2018)

Volume 14 (2018): Issue 3 (September 2018)

Volume 14 (2018): Issue 2 (June 2018)

Volume 14 (2018): Issue 1 (March 2018)

Volume 13 (2017): Issue 4 (December 2017)

Volume 13 (2017): Issue 3 (September 2017)

Volume 13 (2017): Issue 2 (June 2017)

Volume 13 (2017): Issue 1 (March 2017)

Volume 12 (2016): Issue 4 (December 2016)

Volume 12 (2016): Issue 3 (September 2016)

Volume 12 (2016): Issue 2 (June 2016)

Volume 12 (2016): Issue 1 (March 2016)

Volume 11 (2015): Issue 4 (December 2015)

Volume 11 (2015): Issue 3 (September 2015)

Volume 11 (2015): Issue 2 (May 2015)

Volume 11 (2015): Issue 1 (March 2015)

Volume 10 (2014): Issue 4 (December 2014)

Volume 10 (2014): Issue 3 (September 2014)

Volume 10 (2014): Issue 2 (June 2014)

Volume 10 (2014): Issue 1 (March 2014)

Volume 9 (2013): Issue 4 (December 2013)

Volume 9 (2013): Issue 3 (September 2013)

Volume 9 (2013): Issue 2 (June 2013)

Volume 9 (2013): Issue 1 (March 2013)

Modelling in Civil Environmental Engineering

The roots of the Technical University of Civil Engineering of Bucharest (UTCB) go back in 1818 in the school of engineering concerning surveying and geodesy. In 1864 it became the "School of Bridges and Roads, Mines and Architecture", and from 1867 the "School of Bridges, Roads and Mines" and "the National School for Bridges and Roads" in 1888. In 1921, the "National School of Bridges and Roads" became the "Polytechnic School of Bucharest", where the civil engineers' training was carried out in the Civil Engineering Department which, in 1938, came to be known as the Faculty of Civil Engineering.  In 1948, due to the large development of the construction sector in Romania, an important part of the Polytechnic School was separated as the Civil Engineering Institute, including not only the Faculty of Civil Engineering, but also parts of other specializations related to constructions, as building services engineering, mechanical engineering for constructions, hydrotechnical engineering, roads, bridges, and railways construction or geodesy.  Starting from 1994, the Civil Engineering Institute became the Technical University of Civil Engineering Bucharest (UTCB).  The scientific results were published internally in the university scientific bulletin. Since 2005, the scientific bulletin of UTCB became the Mathematical Modelling in Civil Engineering journal.  The journal serves the Civil and Environmental Engineering community and our societies, aiming to effectively contribute to the development, innovation and progress in the field. Our journal publishes papers that present the state-of the-art results from research and practice.  Starting with 2021, the journal Mathematical Modelling in Civil Engineering expands its research fields and thus becomes: Modelling in Civil and Environmental Engineering, with a new ISSN: 2784-1391.  The journal Modelling in Civil and Environmental Engineering covers a wide range of topics from Civil and Environmental Engineering field and is ready to publish high quality standards, state-of the-art, peer-reviewed papers, coming from the academic and research community, and industry as well. MCEE addresses both theoretical developments and practical applications related to Civil and Structural Engineering, Geotechnics and Environmental Science (Soil, Water and Air Pollution, Wastewater Treatment Engineering), Thermal Sciences and Engineering (Thermodynamics, Transport Phenomena, Building Heat &amp; Mass Transfer, HVAC &amp; R), Hydraulic and Wind Engineering, Mechanical and Electrical Engineering in the Built Environment, Automation in Constructions, Roads, Bridges and Railways Constructions, Surveying and Geodesy and any other topics related to constructions and the built environment.  To be acceptable for publication in the MCEE journal, a manuscript must address valuable and of significant interest scientific issues for the Civil Engineering community, free of evident commercial or private interest.  The authors are requested to make sure that appropriate research ethical standards are strictly followed in their work, when submitted to MCEE.　  The MCEE staff fully supports the authors during the entire evaluation process and is committed to ensure that the ethical standards, related to submittal, review, and publication of manuscripts, will be strictly followed.  Rejection rate   22%   Archiving  Sciendo archives the contents of this journal in Portico - digital long-term preservation service of scholarly books, journals and collections.  Plagiarism Policy  The editorial board is participating in a growing community of Similarity Check System's users in order to ensure that the content published is original and trustworthy. Similarity Check is a medium that allows for comprehensive manuscripts screening, aimed to eliminate plagiarism and provide a high standard and quality peer-review process. 