<abstract xml:lang="en"><title style='display:none'>Determination of Load Angle for Salient-pole Synchronous Machine</title>This paper presents two methods for load angle determination for salient-pole synchronous generator. The first method uses optical encoder to detect the rotor position. In some cases the end of the rotor shaft is not free to be used and mounting of an encoder is impossible. Therefore, the second method proposes estimation of the load angle based on the measured electrical values that have been already used in excitation control system of the synchronous generator. Estimation method uses corresponding voltage-current vector diagram and parameters of the synchronous generator, transformer and transmission lines. Both methods were experimentally verified on the digital control system and synchronous generator connected to power system. The estimation and measured results were compared. The accuracy of load angle estimation method depends on voltage and current measurement accuracy as well as generator, transformer and transmission line parameter accuracy. The estimation method gives satisfactory accuracy for load angles less than 120° el. Thus, it can be applied in excitation control system to provide stable work of synchronous generator in under-excitation operating area.</abstract>

Determination of Load Angle for Salient-pole Synchronous Machine

<abstract>This paper analyzes the decoupling of a sliding structure six-axis force/torque sensor, which is used to measure the interactive force between surgical tools and soft tissue for the establishment of soft-tissue force model. Because this decoupling structure requires accurate sliding clearance and symmetric grooves, the influence of contact force between the elastic body and the groove sidewall on decoupling is analyzed. The analysis results indicate that the contact force will produce additional coupling error. The robust design method of elastic body size optimization is used to eliminate the influence of contact force. In the calibration test, the expanded uncertainty of the calibration device is evaluated and the calibration results validate the good decoupling.</abstract>

Decoupling Analysis of a Sliding Structure Six-axis Force/Torque Sensor

<abstract>SIFT is an image local feature description algorithm based on scale-space. Due to its strong matching ability, SIFT has many applications in different fields, such as image retrieval, image stitching, and machine vision. After SIFT was proposed, researchers have never stopped tuning it. The improved algorithms that have drawn a lot of attention are PCA-SIFT, GSIFT, CSIFT, SURF and ASIFT. In this paper, we first systematically analyze SIFT and its variants. Then, we evaluate their performance in different situations: scale change, rotation change, blur change, illumination change, and affine change. The experimental results show that each has its own advantages. SIFT and CSIFT perform the best under scale and rotation change. CSIFT improves SIFT under blur change and affine change, but not illumination change. GSIFT performs the best under blur change and illumination change. ASIFT performs the best under affine change. PCA-SIFT is always the second in different situations. SURF performs the worst in different situations, but runs the fastest.</abstract>

The Institute of Intelligent Information Processing and Application, Soochow University, Suzhou 215006, China

Department of Computer Science, University of Central Arkansas, Conway 72035, USA

A Comparative Study of SIFT and its Variants

<abstract xml:lang="en"><title style='display:none'>Application of Wavelet Analysis in EMG Feature Extraction for Pattern Classification</title>Nowadays, analysis of electromyography (EMG) signal using wavelet transform is one of the most powerful signal processing tools. It is widely used in the EMG recognition system. In this study, we have investigated usefulness of extraction of the EMG features from multiple-level wavelet decomposition of the EMG signal. Different levels of various mother wavelets were used to obtain the useful resolution components from the EMG signal. Optimal EMG resolution component (sub-signal) was selected and then the reconstruction of the useful information signal was done. Noise and unwanted EMG parts were eliminated throughout this process. The estimated EMG signal that is an effective EMG part was extracted with the popular features, i.e. mean absolute value and root mean square, in order to improve quality of class separability. Two criteria used in the evaluation are the ratio of a Euclidean distance to a standard deviation and the scatter graph. The results show that only the EMG features extracted from reconstructed EMG signals of the first-level and the second-level detail coefficients yield the improvement of class separability in feature space. It will ensure that the result of pattern classification accuracy will be as high as possible. Optimal wavelet decomposition is obtained using the seventh order of Daubechies wavelet and the forth-level wavelet decomposition.</abstract>

Application of Wavelet Analysis in EMG Feature Extraction for Pattern Classification

<abstract xml:lang="en"><title style='display:none'>Probing System Characteristics in Coordinate Metrology</title>This paper aims at studying the effect of the dynamic errors on surface measurements using three different types of touch trigger probes attached to a bridge-type-CMM. Unforeseeable dynamic root errors of a ductile touch trigger probing system have been characterized theoretically and experimentally as well. The results were employed in validating a developed analytical two-dimensional-model (2DM) of stylus tip to be developed to demonstrate the capability of such approaches of emphasizing the root error concept, and to evaluate the accuracy of the CMM measurements. A set of experiments was conducted; the results were analyzed in order to investigate the effect of the dynamic root errors in the light of probe scanning speed at different stylus tip radii. Variations in the mass and geometry of the stylus have their consequent effects on its inherent intrinsic dynamic characteristics that in turn would cause relevant systematic root errors in the resulting measurements. 3D bore cylindrical surface form undulations were measured by employing a probe on the trajectory of internal surface diameter for the standard reference test gauge ring. Regression analysis was applied on the results of measurement density distribution; uncertainty of measurement repeatability was then evaluated and graphically presented. The results were investigated and optimum strategic measurement parameters could thus have been derived to ensure foreseeable accurate and precise results.</abstract>

Probing System Characteristics in Coordinate Metrology

<abstract xml:lang="en"><title style='display:none'>Denoising EOG Signal using Stationary Wavelet Transform</title>Eye movements are critical signs of the neurological disorders and they can be acquired by EOG. The EOG signal is electrical signal generated due to eye ball movements and is contaminated with brain signals and power line while recording. As the EOG signal is a non-stationary signal, it can be denoised by wavelet transformation techniques. The present work covers denoising of noisy EOG signal using Stationary Wavelet Transform (SWT), which was done with all suitable wavelets that are morphologically similar to an EOG signal by applying both Soft and Hard Thresholding methods. An EOG signal was simulated and added with noise to obtain noisy EOG signal. The wavelet analysis of the simulated noisy EOG signal reveals that the Biorthogonal 3.3 wavelet is the best wavelet to denoise by using SWT technique, wherein the yield achieved was good with Signal to Noise Ratio of 36.5882 dB and minimum Mean Square Error of 0.383313 for quality diagnosis.</abstract>

Department of Physics, Jawaharlal Nehru Technological University Hyderabad, Hyderabad-3, India

Department of Electrical Engineering, IIT Bombay, India

Department of Biomedical Engineering, Osmania University, Hyderabad-7

Denoising EOG Signal using Stationary Wavelet Transform

<abstract>
<title style='display:none'>Abstract</title>
In order to accurately measure the flight trajectory of the projectile in a long-distance target range, it is important to establish a vertical target measurement system with a two-line array camera at several positions along the range. In the present work, a calibration system using dual theodolites is proposed to calibrate the vertical target measurement system of a dual linear array camera at different positions along a long target range. The present study investigates the principle of intersection measurement in the vertical target measurement system with a double linear array camera and presents the projectile’s target coordinate measurement formula. The calibration method of the measurement system is developed based on an analysis of the parameters in the projectile coordinate measurement formula. The calibration method only requires calibration of the camera’s distortion coefficient, the optical axis angle, and the principal point, ensuring a simplified and expedited calibration process. After calibration, the vertical target measurement system with a 3 m × 3 m measurement area is simulated and analyzed, yielding an error distribution diagram and identifying the factors that influence the measurement accuracy of the projectile’s target coordinates.
</abstract>

Research on the Measurement System and Remote Calibration Technology of a Dual Linear Array Camera

<abstract>
<title style='display:none'>Abstract</title>
Underwater Wireless Sensor Networks (UWSNs) are established by Autonomous Underwater Vehicles (AUVs) or static Sensor Nodes (SN) that collect and transmit information over the underwater environment. Localization plays a vital role in the effective deployment, navigation and coordination of these nodes for many applications, namely underwater surveillance, underwater exploration, oceanographic data collection and environmental monitoring. Due to the unique characteristics of underwater transmission and acquisition, this is a fundamental challenge in underwater networks. However, localization in UWSNs is problematic due to the unique features of underwater transmission and the harsh underwater environment. To address these challenges, this paper presents an Improved Grey Wolf Optimization Based Node Localization Approach in UWSN (IGWONL-UWSN) technique. The presented IGWONL-UWSN technique is inspired by the hunting behavior of grey wolves with the Dimension Learning-based Hunting (DLH) search process. The proposed IGWONL-UWSN technique uses the Improved Grey Wolf Optimization Based (IGWO) algorithm to calculate the optimal location of the nodes in the UWSN. Moreover, the IGWONL-UWSN technique incorporates the DLH search process to improve the convergence and accuracy. The simulation results of the IGWONL-UWSN technique are validated using a set of performance measures. The simulation results show the improvements of the IGWONL-UWSN method over other approaches with respect to various metrics.
</abstract>

Improved Grey Wolf Optimization Based Node Localization Approach in Underwater Wireless Sensor Networks

<abstract>
<title style='display:none'>Abstract</title>
New communication paradigms have emerged to make better use of the available wireless spectrum due to its scarcity. Millimeter wave high-frequency spectrum could offer a viable solution to the problem of spectrum scarcity. Millimeter wave devices and antennas are becoming increasingly popular and are used in a wide variety of applications and planned Fifth Generation (5G) wireless communication networks. In this work, we develop a Substrate Integrated Waveguide (SIW) based antenna array and millimeter-wave feeding network with the aim of achieving optimal performance. A microstrip array antenna is developed for use at millimeter wave frequencies of 28 GHz and 38 GHz. Next, an SIW array antenna will be created. For high-frequency uses, SIW technology excels due to its low loss, easy integration and high quality factor. The two unequal longitudinal slots in a slotted SIW antenna cause the structure to resonate at 28 GHz and 38 GHz. The SIW structure is fabricated by making two parallel rows of metallic vias, carefully determined through sizes to ensure minimal internal losses. A microstrip line that transitions into a SIW feeds into the proposed layout. In this paper, the authors investigate the design and construction of an integrated waveguide antenna array for use at dual millimeter-wave frequencies.
</abstract>

Design and Development of Dual Band Millimeter Wave Substrate Integrated Waveguide Antenna Array

<abstract>
<title style='display:none'>Abstract</title>
Wireless Multimedia Sensor Networks (WMSNs) are networks consisting of sensors that have limitations in terms of memory, computational power, bandwidth and battery life. Multimedia transmission using Wireless Sensor Network (WSN) is a difficult task because certain Quality of Service (QoS) guarantees are required. These guarantees include a large quantity of bandwidth, rigorous latency requirements, improved packet delivery and lower loss ratio. The main area of research would be to investigate the process of greedy techniques that could be modified to guarantee QoS provisioning for multimedia traffic in WSNs. This could include optimization of routing decisions, dynamic allocation of resources and effective congestion management. This study introduces a framework called Epsilon Greedy Strategy based Routing Protocol (EGS-RP) for multimedia content transmission over WSN. The framework focuses on energy efficiency and QoS by using reinforcement learning to optimize rewards. These incentives are determined by a number of variables, including node residual energy, communication energy and the effectiveness of sensor type-dependent data collection. Experimental analysis was conducted to evaluate the effectiveness of the proposed routing strategy and compare it with the performance of standard energy-aware routing algorithms. The proposed EGS-RP achieves a throughput of 217 kbps, a bandwidth of 985 bps, a packet delivery ratio of 94.45% and an energy consumption of 32%.
</abstract>

Improving Quality of Service (QoS) in Wireless Multimedia Sensor Networks using Epsilon Greedy Strategy

<abstract>
<title style='display:none'>Abstract</title>
This article presents a study carried out on a 2 kN·m torque transducer at the Central Office of Measures (GUM) and the Physikalisch-Technische Bundesanstalt (PTB). The weighted least squares method was used to generate the linear regression equations for this torque transducer. The Monte Carlo method and the law of uncertainty propagation were used to calculate the expanded uncertainty. In addition, a creep study was carried out at eight measurement points ranging from 200 N·m to 2000 N·m. The investigations showed that the highest readings of the torque transducer, expressed in electrical units as mV/V, occur within the initial few seconds of the test after the removal of the maximum reference torque.
</abstract>

Study of a 2 kN·m Torque Transducer Tested at GUM and PTB, Including Creep Behaviour

<abstract>
<title style='display:none'>Abstract</title>
Millions of people worldwide suffer from diabetes, a medical condition that is spreading at an accelerating pace. Numerous studies show that risk factors that may arise from diabetes can be avoided if the disease is detected early. The health-care monitoring system has benefited greatly from early diabetes prediction made possible by the integration of Deep Learning (DL) and Machine Learning (ML) algorithms. The objective of many early studies was to increase the prediction model accuracy. However, DL algorithms often cannot fully exploit the potential of the available datasets because they are too small. This study includes a very accurate DL model as well as a novel system that integrates cloud services and allows users to directly enhance an existing data set, which can increase the accuracy of DL techniques. Therefore, the Long Short-Term Memory (LSTM) model with controller is chosen for efficient type-1 diabetes prediction. Experimental validation of the proposed Nonlinear Model Predictive Control (NMPC)_LSTM algorithm method is compared with other conventional DL algorithms. The proposed controller method achieves excellent blood glucose set point tracking and the proposed algorithms achieves 98.95% accuracy for the obtained data. It outperforms other existing methods with an increase in percentage accuracy compared to the Benchmark Pima Indian Diabetes Datasets (PIDD).
</abstract>

A Cloud-Connected Digital System for Type-1 Diabetes Prediction using Time Series LSTM Model

<abstract><title style='display:none'>Abstract</title>Nowadays detection of deterioration of electrical motors is an important topic of research. Vibration signals often carry diagnostic information of a motor. The authors proposed a setup for the analysis of vibration signals of three-phase induction motors. In this paper rotor fault diagnostic techniques of a three-phase induction motor (TPIM) were presented. The presented techniques used vibration signals and signal processing methods. The authors analyzed the recognition rate of vibration signal readings for 3 states of the TPIM: healthy TPIM, TPIM with 1 broken bar, and TPIM with 2 broken bars. In this paper the authors described a method of the feature extraction of vibration signals Method of Selection of Amplitudes of Frequencies – MSAF-12. Feature vectors were obtained using FFT, MSAF-12, and mean of vector sum. Three methods of classification were used: Nearest Neighbor (NN), Linear Discriminant Analysis (LDA), and Linear Support Vector Machine (LSVM). The obtained results of analyzed classifiers were in the range of 97.61 % – 100 %.</abstract>

Detection of Deterioration of Three-phase Induction Motor using Vibration Signals

<abstract>This study presents the variations of photoplethysmogram (PPG) morphology with age. PPG measurement is done noninvasively at the index finger on both right and left hands for a sample of erectile dysfunction (ED) subjects. Some parameters are derived from the analysis of PPG contour showed in association with age. The age is found to be an important factor that affects the contour of PPG signals which accelerates the disappearance of PPG’s dicrotic notch and PPG’s inflection point as well. Arterial compliance is found to be degraded with age due to the fall of arterial elasticity. This study approaches the establishment of usefulness of PPG’s contour analysis as an investigator to the changes in the elastic properties of the vascular system, and as a detector of early sub-clinical atherosclerosis.</abstract>

College of computer science and engineering Taibah University, Madinah-Saudi Arabia

Department of Electrical, Electronic and Systems Engineering, University Kebangsaan Malaysia, 43600 UKM, Bangi, Selangor, Malaysia

The Analysis of PPG Morphology: Investigating the Effects of Aging on Arterial Compliance

<abstract><title style='display:none'>Abstract</title> In this paper, the selected results of measurements and analysis of the active surfaces of a new generation of coated abrasive tools obtained by the use of focus-variation microscopy (FVM) are presented and discussed. The origin of this technique, as well as its general metrological characteristics is briefly described. Additionally, information regarding the focus variation microscope used in the experiments - InfiniteFocus® IF G4 produced by Alicona Imaging, is also given. The measurements were carried out on microfinishing films (IMFF), abrasive portable belts with Cubitron™ II grains, and single-layer abrasive discs with Trizact™ grains. The obtained results were processed and analyzed employing TalyMap 4.0 software in the form of maps and profiles, surface microtopographies, Abbott- Firestone curves, and calculated values of selected areal parameters. This allowed us to describe the active surfaces of the coated abrasive tools, as well as to assess the possibility of applying the FVM technique in such kinds of measurements.</abstract>

Subject Group of Metrology and Quality, Department of Production Engineering, Faculty of Mechanical Engineering, Koszalin University of Technology, Racławicka 15-17, 75-620 Koszalin, Poland

Department of Production Engineering, Faculty of Mechanical Engineering, Koszalin University of Technology, Racławicka 15-17, 75-620 Koszalin, Poland

Faculty of Mechanical Engineering, Opole University of Technology, Prószkowska 76, 45-758 Opole, Poland

The Use of Focus-Variation Microscopy for the Assessment of Active Surfaces of a New Generation of Coated Abrasive Tools

<abstract xml:lang="en"><title style='display:none'>Multi-Wavelength Interferometry for Length Measurements Using Diode Lasers</title>This paper describes the principle of precise length measurements using multi-wavelength interferometry. Three different examples are given in order to demonstrate PTB's ability in this field: 1) Measurements of absolute distances up to 10 m performed by combination of the variable wavelength interferometry with fixed wavelength interferometry using two wavelengths simultaneously, 2) a three-wavelength diode laser interferometer for precision measurements of surface profiles (&lt; 100 μm) and 3) PTB's Precision Interferometer for length measurements of prismatic bodies, e.g. gauge blocks, using three wavelengths. The setup and principle of measurements and some results are presented and discussed in each case.</abstract>

Multi-Wavelength Interferometry for Length Measurements Using Diode Lasers

Open Access License

Guide for Authors

Measurement Science Review

The Journal of Institute of Measurement Science of Slovak Academy of Sciences

 The aim of the journal is to publish papers from scientific disciplines covering the Measurement science with an orientation toward the theory of measurement, measurement of...

Impact Factor

Five Year Impact Factor

Cite Score

SNIP

MNiSW

Google Scholar h5-index

Google Scholar h5-median

 The aim of the journal is to publish papers from scientific disciplines covering the Measurement science with an orientation toward the...

Measurement Science Review

The Journal of Institute of Measurement Science of Slovak Academy of Sciences

Alle Bände und Hefte dieser Zeitschrift