<abstract xmlns="http://www.w3.org/1999/xhtml">

<sec>
<h3>Aim</h3>
<p>To determine the shear bond strengths (SBS) of stainless steel brackets bonded with seven light-cured orthodontic adhesives after the enamel was conditioned with the same self-etching primer.</p>
</sec>
<sec>
<h3>Methods</h3>
<p>A total of 140 extracted human molars were randomly divided into seven groups (N = 20). In all the groups, the enamel was conditioned with Transbond Plus SEP (TPSEP). Stainless steel brackets were bonded with the following orthodontic adhesives: Group I, Transbond XT; Group II, Blūgloo; Group III, BeautyOrtho Bond; Group IV, Enlight; Group V, Light Bond; Group VI, Transbond CC; Group VII, Xeno Ortho. The teeth were stored in distilled water at 37 °C for 24 hours and debonded with a universal testing machine. The modified adhesive remnant index (ARI) was also recorded.</p>
</sec>
<sec>
<h3>Results</h3>
<p>There were no significant differences in the SBS values among the groups: I (18.0 ± 7.4 MPa); II (18.3 ± 5.1 MPa); III (14.8 ± 4.3 MPa); IV (18.3 ± 7.0 MPa); V (16.4 ± 4.3 MPa); VI (20.3 ± 5.3 MPa); VII (15.9 ± 6.4 MPa), but significant differences in ARI were found.</p>
</sec>
<sec>
<h3>Conclusions</h3>
<p>The seven orthodontic adhesives evaluated in this study can be successfully used for bonding stainless steel brackets when the enamel is conditioned with TPSEP, however, the differences among some groups might influence the clinical bond strengths. In addition, the amount of residual adhesive remaining on the teeth after debonding differed among the adhesives. Further studies are required to better understand the differences in SBS and ARI.</p>
</sec>
</abstract>

Aim
To determine the shear bond strengths (SBS) of stainless steel brackets bonded with seven light-cured orthodontic adhesives after the enamel was conditioned with the same self-etching primer.


Methods
A total of 140 extracted human molars were randomly divided into seven groups (N = 20). In all the groups, the enamel was conditioned with Transbond Plus SEP (TPSEP). Stainless steel brackets were bonded with the following orthodontic adhesives: Group I, Transbond XT; Group II, Blūgloo; Group III, BeautyOrtho Bond; Group IV, Enlight; Group V, Light Bond; Group VI, Transbond CC; Group VII, Xeno Ortho. The teeth were stored in distilled water at 37 °C for 24 hours and debonded with a universal testing machine. The modified adhesive remnant index (ARI) was also recorded.


Results
There were no significant differences in the SBS values among the groups: I (18.0 ± 7.4 MPa); II (18.3 ± 5.1 MPa); III (14.8 ± 4.3 MPa); IV (18.3 ± 7.0 MPa); V (16.4 ± 4.3 MPa); VI (20.3 ± 5.3 MPa); VII (15.9 ± 6.4 MPa), but significant differences in ARI were found.


Conclusions
The seven orthodontic adhesives evaluated in this study can be successfully used for bonding stainless steel brackets when the enamel is conditioned with TPSEP, however, the differences among some groups might influence the clinical bond strengths. In addition, the amount of residual adhesive remaining on the teeth after debonding differed among the adhesives. Further studies are required to better understand the differences in SBS and ARI.

Bond strengths of different orthodontic adhesives after enamel conditioning with the same self-etching primer

Australasian Orthodontic Journal

This work is licensed under the Creative Commons Attribution 4.0 International License.

Aim
To determine the shear bond strengths (SBS) of stainless steel brackets bonded with seven light-cured orthodontic adhesives after the enamel was...

Bond strengths of different orthodontic adhesives after enamel conditioning with the same self-etching primer

Data publikacji: 14 gru 2023

Zakres stron: 84 - 89

Otrzymano: 01 gru 2008

Przyjęty: 01 lut 2010

DOI: https://doi.org/10.2478/aoj-2010-0015

© 2010 Rogelio J. Scougall-Vilchis et al., published by Sciendo

This work is licensed under the Creative Commons Attribution 4.0 International License.