Logowanie
Zarejestruj się
Zresetuj hasło
Publikuj i Dystrybuuj
Rozwiązania Wydawnicze
Rozwiązania Dystrybucyjne
Dziedziny
Architektura i projektowanie
Bibliotekoznawstwo i bibliologia
Biznes i ekonomia
Chemia
Chemia przemysłowa
Filozofia
Fizyka
Historia
Informatyka
Inżynieria
Inżynieria materiałowa
Językoznawstwo i semiotyka
Kulturoznawstwo
Literatura
Matematyka
Medycyna
Muzyka
Nauki farmaceutyczne
Nauki klasyczne i starożytne studia bliskowschodnie
Nauki o Ziemi
Nauki o organizmach żywych
Nauki społeczne
Prawo
Sport i rekreacja
Studia judaistyczne
Sztuka
Teologia i religia
Zagadnienia ogólne
Publikacje
Czasopisma
Książki
Materiały konferencyjne
Wydawcy
Blog
Kontakt
Wyszukiwanie
EUR
USD
GBP
Polski
English
Deutsch
Polski
Español
Français
Italiano
Koszyk
Home
Czasopisma
Architecture, Civil Engineering, Environment
Tom 16 (2023): Zeszyt 3 (September 2023)
Otwarty dostęp
The Analysis of Pile Skin and Base Resistances Interaction Based on Static Pile Load Test in Experimental Research
Krzysztof Żarkiewicz
Krzysztof Żarkiewicz
| 20 paź 2023
Architecture, Civil Engineering, Environment
Tom 16 (2023): Zeszyt 3 (September 2023)
O artykule
Poprzedni artykuł
Następny artykuł
Abstrakt
Artykuł
Ilustracje i tabele
Referencje
Autorzy
Artykuły w tym zeszycie
Podgląd
PDF
Zacytuj
Udostępnij
Data publikacji:
20 paź 2023
Zakres stron:
141 - 150
Otrzymano:
23 sty 2023
Przyjęty:
29 mar 2023
DOI:
https://doi.org/10.2478/acee-2023-0041
Słowa kluczowe
Pile
,
Pile skin friction
,
Pile base resistance
© 2023 Krzysztof Żarkiewicz, published by Sciendo
This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Figure 1.
Pressure mapping system used in measurement stress in soil. a) the sensor with data logger; b) zoom on sensel
Figure 2.
Grain size distribution of the soil used in the research
Figure 3.
Schemes of tests with measurement instrumentation
Figure 4.
Outcomes from static pile load test. Where N2 – axial load applied at pile head, N1 – pile base resistance, T – pile skin resistance, s – pile head settlement. a) Pile 1, b) Pile 2, c) Pile 3, d) Pile 4
Figure 5.
Example of stress measured by the pressure mapping system of Pile 1 at the load N2 = 2.18 kN. a) Pressure map from one step of load; b) Outcomes as the average values over a band of vertical component of stress is soil versus distance from pile skin (r–r0) with proposed approximation
Figure 6.
Stress in soil σv,s,0 versus pile skin and base resistance close to the pile skin at the level of pile base where T=N2-N1. a) Pile 1; b) Pile 2
Figure 7.
Calculated stresses v,s,o versus measurements. a) Pile 1; b) Pile 2
Figure 8.
Example of stress measured by pressure mapping system of Pile 3 as an average over the entire area, at load N2 =1.91 kN, and settlement s=0.97 mm. a) Pressure map from one step of load; b) Outcomes of the vertical component of stress is soil versus distance from pile axis (r) with proposed approximation
Figure 9.
Stress in soil σv,s,0 versus axial force in pile head N2 50 mm beneath the pile base Pile 3 and Pile 4
Figure 10.
Calculated ratio of stresses σv,b,0 / σv,s,0 versus settlement. a) Pile 1; b) Pile 2