<abstract xmlns="http://www.w3.org/1999/xhtml">

<p>A thermopile is an electronic device that converts thermal energy into electrical energy by means of arrangements of thermocouples that are connected in series. In addition, optical filters restrict the wavelength that strikes the thermopile. One of the main advantages of using a thermopile is its sensitivity to infrared radiation, which allows implementing non-contact thermometers. However, the thermopile does not provide an absolute temperature value, but a value that is proportional to the temperature gradient between the local temperature in th e measurement range of the thermopile and its internal temperature. Therefore, it is necessary to integrate temperature sensors aiming to correct the output temperature value. In this sense, the output of the thermopile corresponds to a value generatedfrom the relationship between the internal temperature of the thermopile and the output temperature. This work proposes and evaluates a thermopile characterization model, which uses an incubation system and a thermoelectric cooling device to control the room temperature and the temperature that is read out using the thermopile, respectively. This is based on the automation of the data collection procedure and the characterization of the thermistor that is used to measure the temperature of the thermopile. The result is an experimental operating surface, from which a linearization model was derived</p>
</abstract>

A thermopile is an electronic device that converts thermal energy into electrical energy by means of arrangements of thermocouples that are connected in series. In addition, optical filters restrict the wavelength that strikes the thermopile. One of the main advantages of using a thermopile is its sensitivity to infrared radiation, which allows implementing non-contact thermometers. However, the thermopile does not provide an absolute temperature value, but a value that is proportional to the temperature gradient between the local temperature in th e measurement range of the thermopile and its internal temperature. Therefore, it is necessary to integrate temperature sensors aiming to correct the output temperature value. In this sense, the output of the thermopile corresponds to a value generatedfrom the relationship between the internal temperature of the thermopile and the output temperature. This work proposes and evaluates a thermopile characterization model, which uses an incubation system and a thermoelectric cooling device to control the room temperature and the temperature that is read out using the thermopile, respectively. This is based on the automation of the data collection procedure and the characterization of the thermistor that is used to measure the temperature of the thermopile. The result is an experimental operating surface, from which a linearization model was derived

An Inverse Linearization Model for the Characterization of Non-Contact Thermopiles

Facultad de Ingenierías, Instituto Tecnológico Metropolitano ITM

International Journal on Smart Sensing and Intelligent Systems

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

A thermopile is an electronic device that converts thermal energy into electrical energy by means of arrangements of thermocouples that are connected in...

An Inverse Linearization Model for the Characterization of Non-Contact Thermopiles

Data publikacji: 01 cze 2016

Zakres stron: 637 - 650

Otrzymano: 16 gru 2015

Przyjęty: 20 mar 2016

DOI: https://doi.org/10.21307/ijssis-2017-888

Słowa kluczowe
Linearization, non-contact, thermopile, Peltier effect, thermistor

© 2016 J-S. Botero et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

An Inverse Linearization Model for the Characterization of Non-Contact Thermopiles

Data publikacji: 01 cze 2016

Zakres stron: 637 - 650

Otrzymano: 16 gru 2015

Przyjęty: 20 mar 2016

DOI: https://doi.org/10.21307/ijssis-2017-888

Słowa kluczoweLinearization, non-contact, thermopile, Peltier effect, thermistor

© 2016 J-S. Botero et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Słowa kluczowe
Linearization, non-contact, thermopile, Peltier effect, thermistor