<abstract xmlns="http://www.w3.org/1999/xhtml">

This study was performed to determine the effects of the densification process and glue type in wood material on dowel tensile performance. For this purpose, 8 mm and 10 mm diameter dowels were obtained from black poplar (<italic>Populus nigra</italic>) and Eastern spruce (<italic>Picea orientalis L</italic>.), which were densified at 50% and 75% ratios. The dowels were bonded with PVAc and D-VTKA glue separately after drilling 18 mm deep holes in the edge of the melamine-coated particleboard. The tensile performance test was determined with the Universal test device according to TS 2475 and ASTM-D 1035 principles. As a result, Eastern spruce wood had the highest tensile performance (kg/cm2), and poplar wood had the lowest (173.66). For the dowel diameter parameter, the highest value (195.11) was found at 8 mm in diameter and the lowest value (161.05) was found at 10 mm in diameter. In terms of glue type, the highest value (185.92) was seen at PVAc while the lowest value (170.24) was seen at D-VTKA. And for the densification ratios, the highest value (191.4) was determined at 75%, while the lowest value was found in control samples at (167.4). According to the wood species, densification ratio, dowel diameter and glue type interaction, the highest value was determined at Es + d75% + 10mm + PVAc as (303.5) and the lowest value was found at P + d50% + 10mm + Dv as (110).
As a result, where the dowel's high tensile performance is sought, using a 10 mm diameter dowel made from 75% densified spruce wood with PVAc glue may be advantageous.
</abstract>

This study was performed to determine the effects of the densification process and glue type in wood material on dowel tensile performance. For this purpose, 8 mm and 10 mm diameter dowels were obtained from black poplar (Populus nigra) and Eastern spruce (Picea orientalis L.), which were densified at 50% and 75% ratios. The dowels were bonded with PVAc and D-VTKA glue separately after drilling 18 mm deep holes in the edge of the melamine-coated particleboard. The tensile performance test was determined with the Universal test device according to TS 2475 and ASTM-D 1035 principles. As a result, Eastern spruce wood had the highest tensile performance (kg/cm2), and poplar wood had the lowest (173.66). For the dowel diameter parameter, the highest value (195.11) was found at 8 mm in diameter and the lowest value (161.05) was found at 10 mm in diameter. In terms of glue type, the highest value (185.92) was seen at PVAc while the lowest value (170.24) was seen at D-VTKA. And for the densification ratios, the highest value (191.4) was determined at 75%, while the lowest value was found in control samples at (167.4). According to the wood species, densification ratio, dowel diameter and glue type interaction, the highest value was determined at Es + d75% + 10mm + PVAc as (303.5) and the lowest value was found at P + d50% + 10mm + Dv as (110).
As a result, where the dowel's high tensile performance is sought, using a 10 mm diameter dowel made from 75% densified spruce wood with PVAc glue may be advantageous.

The effect of the densification process on dowel tensile performance with different types of glues

Folia Forestalia Polonica

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

This study was performed to determine the effects of the densification process and glue type in wood material on dowel tensile performance. For this purpose, 8...

The effect of the densification process on dowel tensile performance with different types of glues

Article Category: Original Article

Publié en ligne: 10 déc. 2022

Pages: 214 - 225

Reçu: 27 janv. 2022

Accepté: 10 mars 2022

DOI: https://doi.org/10.2478/ffp-2022-0021

Mots clés
dowel tensile performance, densification, wood material, glue, particle boards

© 2022 Ersin Ercan et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

The effect of the densification process on dowel tensile performance with different types of glues

Article Category: Original Article

Publié en ligne: 10 déc. 2022

Pages: 214 - 225

Reçu: 27 janv. 2022

Accepté: 10 mars 2022

DOI: https://doi.org/10.2478/ffp-2022-0021

Mots clésdowel tensile performance, densification, wood material, glue, particle boards

© 2022 Ersin Ercan et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Mots clés
dowel tensile performance, densification, wood material, glue, particle boards