<abstract xmlns="http://www.w3.org/1999/xhtml"><p>The subject of the experimental research was a modified back-to-back test stand. During the test, the driven gear with a number of teeth <italic>z1</italic>=16 was fixed on stationary axis. The tested gearbox worked without load and the closing gearbox was dismantled to avoid any additional vibration and noise. A mechanical system was also used which, during the tests, allowed to change the position of the above mentioned stationary axis. Gear with number of teeth <italic>z1</italic> was fixed on a stationary axis with the arrangement of two self-aligning ball bear-ings which prevented significant changes in the angular position of axis of gear in regard of stationary axis; or fixed on a stationary axis with the arrangement of one self-aligning ball bearing which allowed significant changes in the angular position of axis of gear in regard of stationary axis. On the basis of the conducted studies, it can be stated that only in some of the analyzed cases fixing of gear with the arrangement of one self-aligning ball bearing reduces the vibration of the gearbox elements.</p></abstract>

The subject of the experimental research was a modified back-to-back test stand. During the test, the driven gear with a number of teeth z1=16 was fixed on stationary axis. The tested gearbox worked without load and the closing gearbox was dismantled to avoid any additional vibration and noise. A mechanical system was also used which, during the tests, allowed to change the position of the above mentioned stationary axis. Gear with number of teeth z1 was fixed on a stationary axis with the arrangement of two self-aligning ball bear-ings which prevented significant changes in the angular position of axis of gear in regard of stationary axis; or fixed on a stationary axis with the arrangement of one self-aligning ball bearing which allowed significant changes in the angular position of axis of gear in regard of stationary axis. On the basis of the conducted studies, it can be stated that only in some of the analyzed cases fixing of gear with the arrangement of one self-aligning ball bearing reduces the vibration of the gearbox elements.

The Impact of Non-Parallelism of Toothed Gear Shafts Axes and Method of Gear Fixing on Gearbox Components Vibrations

Acta Mechanica et Automatica

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

The subject of the experimental research was a modified back-to-back test stand. During the test, the driven gear with a number of teeth z1=16 was fixed on...

The Impact of Non-Parallelism of Toothed Gear Shafts Axes and Method of Gear Fixing on Gearbox Components Vibrations

Publicado en línea: 17 jul 2018

Páginas: 165 - 171

Recibido: 13 sept 2017

Aceptado: 30 jun 2018

DOI: https://doi.org/10.2478/ama-2018-0026

Palabras clave
Toothed Gear, Non-Parallelism of Axes, Reduction, Vibration, Self-Aligning Gear Fixing

© 2018 Grzegorz Wojnar et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

The Impact of Non-Parallelism of Toothed Gear Shafts Axes and Method of Gear Fixing on Gearbox Components Vibrations

Publicado en línea: 17 jul 2018

Páginas: 165 - 171

Recibido: 13 sept 2017

Aceptado: 30 jun 2018

DOI: https://doi.org/10.2478/ama-2018-0026

Palabras claveToothed Gear, Non-Parallelism of Axes, Reduction, Vibration, Self-Aligning Gear Fixing

© 2018 Grzegorz Wojnar et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

Palabras clave
Toothed Gear, Non-Parallelism of Axes, Reduction, Vibration, Self-Aligning Gear Fixing