<abstract xmlns="http://www.w3.org/1999/xhtml"><p>Bioimpedance measurement systems often use the Howland current sources to excite the biological material under study. Usually, difference or instrumentation amplifiers are used to measure the resulting voltage drop on this material. In these circuits, common mode voltage appears as artifacts in the measurement. Most researches on current sources are focused on improving the output impedance, letting other characteristics aside. In this paper, it is made a brief review on the load common mode voltage and output swing of various topologies of Howland current sources. Three circuits are proposed to reduce load common mode voltage and enhance load capability by using a fully differential amplifier as active component. These circuits are equated, simulated and implemented. The three proposed circuits were able to deliver an output current with cut-off frequency (-3dB) higher than 1 MHz for loads as big as 4.7 kΩ. The worst measured load common mode voltage was smaller than 24 mV for one of the circuits and smaller than 8 mV for the other two. Consequently, it could be obtained increases in the Common Mode Rejection Ratio (CMRR) up to 60 dB when compared to the Enhanced Howland Current Source (EHCS).</p></abstract>

Bioimpedance measurement systems often use the Howland current sources to excite the biological material under study. Usually, difference or instrumentation amplifiers are used to measure the resulting voltage drop on this material. In these circuits, common mode voltage appears as artifacts in the measurement. Most researches on current sources are focused on improving the output impedance, letting other characteristics aside. In this paper, it is made a brief review on the load common mode voltage and output swing of various topologies of Howland current sources. Three circuits are proposed to reduce load common mode voltage and enhance load capability by using a fully differential amplifier as active component. These circuits are equated, simulated and implemented. The three proposed circuits were able to deliver an output current with cut-off frequency (-3dB) higher than 1 MHz for loads as big as 4.7 kΩ. The worst measured load common mode voltage was smaller than 24 mV for one of the circuits and smaller than 8 mV for the other two. Consequently, it could be obtained increases in the Common Mode Rejection Ratio (CMRR) up to 60 dB when compared to the Enhanced Howland Current Source (EHCS).

Design of current sources for load common mode optimization

Journal of Electrical Bioimpedance

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

{"article-title":"Design of current sources for load common mode optimization"}

Bioimpedance measurement systems often use the Howland current sources to excite the biological material under study. Usually, difference or instrumentation...

Design of current sources for load common mode optimization

Article Category: Research articles

Online veröffentlicht: 19. Dez. 2018

Seitenbereich: 59 - 71

Eingereicht: 15. Mai 2018

DOI: https://doi.org/10.2478/joeb-2018-0011

Schlüsselwörter
Bioimpedance, Howland current source, Common mode rejection

© 2018 Vinicius G. Sirtoli, Kaue F. Morcelles, Volney C. Vincence published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Design of current sources for load common mode optimization

Article Category: Research articles

Online veröffentlicht: 19. Dez. 2018

Seitenbereich: 59 - 71

Eingereicht: 15. Mai 2018

DOI: https://doi.org/10.2478/joeb-2018-0011

SchlüsselwörterBioimpedance, Howland current source, Common mode rejection

© 2018 Vinicius G. Sirtoli, Kaue F. Morcelles, Volney C. Vincence published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Schlüsselwörter
Bioimpedance, Howland current source, Common mode rejection