The Influence of Measurement Methodology on the Accuracy of Electrical Waveform Distortion Analysis

[1] Shmilovitz, D. (2005). On the definition of total harmonic distortion and its effect on measurement interpretation. IEEE Transactions on Power Delivery, 20 (1), 526-528.Search in Google Scholar

[2] Binkowski, T. (2016). Influence of current sampling frequency on voltage source inverter fuzzy correction. In 13th Selected Issues of Electrical Engineering and Electronics (WZEE). IEEE.10.1109/WZEE.2016.7800216Search in Google Scholar

[3] Kamuda, K., Klepacki, D., Kuryło, K. Sabat, W. (2015). Statistical analysis of influence of the low-power nonlinear loads on deformation of supply voltage. Przegląd Elektrotechniczny, 91 (8), 19-22. (in Polish)Search in Google Scholar

[4] Sobczynski, D. (2015). A concept of a power electronic converter for a BLDC motor drive system in aviation. Aviation, 19 (1), 36-39.10.3846/16487788.2015.1015294Search in Google Scholar

[5] Rezmer, J., Leonowicz, Z., Gono, R. (2011). Analysis of distorted waveform in power converter systems. Przegląd Elektrotechniczny, 87 (1), 254-257.Search in Google Scholar

[6] Bartman, J. (2017). The analysis of output voltage distortion of inverter for frequency lower than the nominal. Journal of Electrical Engineering, 68 (3), 194-199.10.1515/jee-2017-0028Search in Google Scholar

[7] Hanzelka, Z., Bień, A. (2004). Harmonics. Interharmonics. Power Quality Application Guide 3.1.1., Copper Development Association.Search in Google Scholar

[8] Bartman, J. (2016). Accuracy of reflecting the waveforms of current and voltage through their spectrum determined by the standards regulating measurements. Revue Roumaine des Sciences Techniques - Serie Électrotechnique et Énergétique, 61 (4), 355-360.Search in Google Scholar

[9] International Electrotechnical Commission. (2015). Electromagnetic compatibility (EMC) – Part 4-30: Testing and measurement techniques – Power quality measurement methods. IEC 61000-4-30: 2015 RLV.Search in Google Scholar

[10] International Electrotechnical Commission. (2002). Electromagnetic compatibility (EMC) – Part 4-7: Testing and measurement techniques - General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto. IEC 61000-4-7: 2002(E).Search in Google Scholar

[11] Bollen, M., Olofsson, M., Larsson, A., Ronnberg, S., Lundmark, M. (2014). Standards for supraharmonics (2 to 150 kHz). IEEE Electromagnetic Compatibility Magazine, 3 (1), 114-119.10.1109/MEMC.2014.6798813Search in Google Scholar

[12] Leszczyński, J. (2010). Research on the quality of electricity: A comparative analysis of methods and regulations. Prace Naukowe: Instytutu Maszyn, Napędów i Pomiarów Elektrycznych Politechniki Wrocławskiej: Studia i Materiały, 30, 520-534. (in Polish)Search in Google Scholar

[13] Bartman, J., Koziorowska, A., Kuryło, K., Malska, W. (2011). Analysis of the real electric parameters feed water-pump drive systems. Przegląd Elektrotechniczny, 87 (8), 8-11. (in Polish)Search in Google Scholar

[14] Koziorowska, A., Bartman, J. (2014). The influence of reactive power compensation on the content of higher harmonics in the voltage and current waveforms. Przegląd Elektrotechniczny, 90 (1), 136-140.Search in Google Scholar

[15] Lin, W. (2012). Current harmonics and interharmonics measurement using Recursive Group-Harmonic Current Minimizing Algorithm. IEEE Transactions on Industrial Electronics, 59 (2), 1184-1193.10.1109/TIE.2011.2157281Search in Google Scholar

[16] Pawłowski, M. (2010). Basics of harmonic analysis of distorted currents and voltages in power supply networks. Mechanizacja i Automatyzacja Górnictwa, 7, 17-23. (in Polish)Search in Google Scholar

[17] Petrović, P. (2012). Frequency and parameter estimation of multi-sinusoidal signal. Measurement Science Review, 12 (5), 175-183.10.2478/v10048-012-0027-4Search in Google Scholar

[18] Knežević, J.M., Katić, V.A. (2011). The hybrid method for on-line harmonic analysis. Advances in Electrical and Computer Engineering, 11 (3), 29-34.10.4316/aece.2011.03005Open DOISearch in Google Scholar

[19] Chapman, D. (2001). Harmonics: Causes and effects. Power Quality Application Guide 3.1., Copper Development Association.Search in Google Scholar

[20] Antić, B.M., Mitrović, Z.L., Vujičić, V.V. (2012), A method for harmonic measurement of real power grid signals with frequency drift using instruments with internally generated reference frequency. Measurement Science Review, 12 (6), 277-285.10.2478/v10048-012-0038-1Search in Google Scholar

[21] Shmilovitz, D., Duan, J., Czarkowski, D., Zabar, Z., Lee, S. (2007). Characteristics of modern nonlinear loads and their influence on systems with distributed generation. International Journal Energy Technology and Policy, 5 (2), 219-240.10.1504/IJETP.2007.013033Search in Google Scholar

[22] Koziorowska, A. Bartman, J. (2012), A-model as a way of squirrel cage induction motor modelling used in pumps drive systems. International Journal of Numerical Modelling, 25, 103-114.10.1002/jnm.814Search in Google Scholar

[23] Mindykowski, J. (2016). Case study based overview of some contemporary challenges to power quality in ship systems. Inventions, 1 (2), 12.10.3390/inventions1020012Search in Google Scholar

[24] Tarasiuk, T., Mindykowski, J. (2015). Problem of power quality in the wake of ship technology development. Ocean Engineering, 107, 108-117.10.1016/j.oceaneng.2015.07.036Search in Google Scholar

[25] Kus, V., Josefova, T. (2017). Study of the input current harmonic distortion of voltage-source active. Revue Roumaine des Sciences Techniques - Serie Électrotechnique et Énergétique, 62 (2), 185-191.Search in Google Scholar

[26] Bartman, J. (2018). Evaluating the level of waveform distortion. In Analysis and Simulation of Electrical and Computer Systems. Springer, 305-318.10.1007/978-3-319-63949-9_19Search in Google Scholar