<abstract xmlns="http://www.w3.org/1999/xhtml"><p>The drilling of small cylindrical (D &lt; 1 mm) holes with a high ratio of length to diameter (L/D > 10) in difficult-to-cut materials is significantly beyond mechanical drilling capabilities. Electrodischarge machining (EDM) is a good and cost effective alternative in such situations. The machinability of electrodischarge machined material is determined by its thermal and electrical properties; therefore, the high electrical resistivity, the relatively high melting point and low thermal conductivity of Ti-6Al-4V alloy cause problems during the machining of parts made of this material. In this article, the results of experimental research on electrodischarge microdrilling in Grade 5 Ti-6Al-4V alloy are presented. The influence of various machining parameters (pulse time, discharge voltage, current amplitude, dielectric pressure, electrode-tool rotation speed) on key technological factors such as hole depth, side gap, linear tool wear, mean drilling speed and hole taper angle was analysed.</p></abstract>

The drilling of small cylindrical (D < 1 mm) holes with a high ratio of length to diameter (L/D > 10) in difficult-to-cut materials is significantly beyond mechanical drilling capabilities. Electrodischarge machining (EDM) is a good and cost effective alternative in such situations. The machinability of electrodischarge machined material is determined by its thermal and electrical properties; therefore, the high electrical resistivity, the relatively high melting point and low thermal conductivity of Ti-6Al-4V alloy cause problems during the machining of parts made of this material. In this article, the results of experimental research on electrodischarge microdrilling in Grade 5 Ti-6Al-4V alloy are presented. The influence of various machining parameters (pulse time, discharge voltage, current amplitude, dielectric pressure, electrode-tool rotation speed) on key technological factors such as hole depth, side gap, linear tool wear, mean drilling speed and hole taper angle was analysed.

Experimental research on electrodischarge drilling of high aspect ratio holes in Ti-6AL-4V alloy

Institute of Production Engineering, Faculty of Mechanical Engineering

Technical Transactions

This work is licensed under the Creative Commons Attribution-ShareAlike 4.0 Public License.

The drilling of small cylindrical (D  10) in difficult-to-cut materials is significantly beyond mechanical drilling capabilities. Electrodischarge machining (EDM) is a good and cost effective alternative in such situations. The machinability of electrodischarge machined material is determined by its thermal and electrical properties; therefore, the high electrical resistivity, the relatively high melting point and low thermal conductivity of Ti-6Al-4V alloy cause problems during the machining of parts made of this material. In this article, the results of experimental research on electrodischarge microdrilling in Grade 5 Ti-6Al-4V alloy are presented. The influence of various machining parameters (pulse time, discharge voltage, current amplitude, dielectric pressure, electrode-tool rotation speed) on key technological factors such as hole depth, side gap, linear tool wear, mean drilling speed and hole taper angle was analysed.

The drilling of small cylindrical (D < 1 mm) holes with a high ratio of length to diameter (L/D > 10) in difficult-to-cut materials is significantly beyond...

Experimental research on electrodischarge drilling of high aspect ratio holes in Ti-6AL-4V alloy

Pubblicato online: 21 mag 2020

Pagine: 171 - 180

Ricevuto: 18 set 2018

DOI: https://doi.org/10.4467/2353737XCT.18.154.9102

Parole chiave
EDM, holes with a high ratio of length to diameter, drilling, titanium

© 2019 Piotr Lipiec et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-ShareAlike 4.0 Public License.

Experimental research on electrodischarge drilling of high aspect ratio holes in Ti-6AL-4V alloy

Pubblicato online: 21 mag 2020

Pagine: 171 - 180

Ricevuto: 18 set 2018

DOI: https://doi.org/10.4467/2353737XCT.18.154.9102

Parole chiaveEDM, holes with a high ratio of length to diameter, drilling, titanium

© 2019 Piotr Lipiec et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-ShareAlike 4.0 Public License.

Parole chiave
EDM, holes with a high ratio of length to diameter, drilling, titanium