<abstract xmlns="http://www.w3.org/1999/xhtml"><p>The article discusses the results of a study investigating the effect of the number of fine non-metallic inclusions (up to 2 μm in size) on the fatigue strength of structural steel during rotary bending. The study was performed on 7 heats produced in an industrial plant. Fourteen heats were produced in a 100 ton oxygen converter. All heats were subjected to vacuum circulation degassing.</p><p>Steel sections with a diameter of 18 mm were hardened and tempered at a temperature of 200, 300, 400, 500 and 600°C. The experimental variants were compared in view of the applied melting technology and heat treatment options. The heat treatments were selected to produce heats with different microstructure of steel, from hard microstructure of tempered martensite, through sorbitol to the ductile microstructure of spheroidite. The results were presented graphically, and the fatigue strength of steel with a varied share of non-metallic inclusions was determined during rotary bending. The results revealed that fatigue strength is determined by the relative volume of fine non-metallic inclusions and tempering temperature.</p></abstract>

The article discusses the results of a study investigating the effect of the number of fine non-metallic inclusions (up to 2 μm in size) on the fatigue strength of structural steel during rotary bending. The study was performed on 7 heats produced in an industrial plant. Fourteen heats were produced in a 100 ton oxygen converter. All heats were subjected to vacuum circulation degassing.Steel sections with a diameter of 18 mm were hardened and tempered at a temperature of 200, 300, 400, 500 and 600°C. The experimental variants were compared in view of the applied melting technology and heat treatment options. The heat treatments were selected to produce heats with different microstructure of steel, from hard microstructure of tempered martensite, through sorbitol to the ductile microstructure of spheroidite. The results were presented graphically, and the fatigue strength of steel with a varied share of non-metallic inclusions was determined during rotary bending. The results revealed that fatigue strength is determined by the relative volume of fine non-metallic inclusions and tempering temperature.

Bending fatigue strength coefficient the low carbon steel with impurities

University of Warmia and Mazury in Olsztyn

Production Engineering Archives

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

{"article-title":"Bending fatigue strength coefficient the low carbon steel with impurities"}

The article discusses the results of a study investigating the effect of the number of fine non-metallic inclusions (up to 2 μm in size) on the fatigue...

Bending fatigue strength coefficient the low carbon steel with impurities

Pubblicato online: 07 mar 2019

Pagine: 20 - 23

Ricevuto: 25 ott 2018

Accettato: 28 nov 2019

DOI: https://doi.org/10.30657/pea.2018.21.04

Parole chiave
steel, structural steel, non-metallic inclusions, oxide impurities, fatigue strength, bending fatigue

© 2018 Tomasz Lipiński, published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Bending fatigue strength coefficient the low carbon steel with impurities

Pubblicato online: 07 mar 2019

Pagine: 20 - 23

Ricevuto: 25 ott 2018

Accettato: 28 nov 2019

DOI: https://doi.org/10.30657/pea.2018.21.04

Parole chiavesteel, structural steel, non-metallic inclusions, oxide impurities, fatigue strength, bending fatigue

© 2018 Tomasz Lipiński, published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Parole chiave
steel, structural steel, non-metallic inclusions, oxide impurities, fatigue strength, bending fatigue