<abstract xmlns="http://www.w3.org/1999/xhtml"><p>Pine wood is commonly used in the production of floorings and is mainly used for solid wood planks and as a base in multi-layer flooring material. From an economic and ecological point of view, flaws such as flattening or heartwood ratio are very important when buying material for production. 40 logs of Scots pine (<italic>Pinus sylvestris</italic> L.) have been selected from wood deposit, from typical wood delivery. The ratios of sapwood and heartwood have been quantified, as well as eccentricity and flattening, in order to determine the suitability of the selected material for processing into floorings. There are two existing methods of log processing: sawing and peripheral cutting. Sawing is the most common one and widely used, although peripheral cutting could be more effective, especially for production of base in multi-layer floorings. The total loss volume for the two methods of manipulation and processing have been calculated. First one is sawing in accordance to schematics used in the sawmill of one of the largest producers of multilayer floorings in Europe. Second one is peripheral cutting with three diameters of peeler roll. Total loss volume for sawing was 55.8 ± 10.5% and for peripheral cutting with peeler roll with biggest chosen diameter of 100 mm was 45.6 ± 9.5%. Therefore, in presented case, peripheral cutting is more efficient than sawing.</p></abstract>

Pine wood is commonly used in the production of floorings and is mainly used for solid wood planks and as a base in multi-layer flooring material. From an economic and ecological point of view, flaws such as flattening or heartwood ratio are very important when buying material for production. 40 logs of Scots pine (Pinus sylvestris L.) have been selected from wood deposit, from typical wood delivery. The ratios of sapwood and heartwood have been quantified, as well as eccentricity and flattening, in order to determine the suitability of the selected material for processing into floorings. There are two existing methods of log processing: sawing and peripheral cutting. Sawing is the most common one and widely used, although peripheral cutting could be more effective, especially for production of base in multi-layer floorings. The total loss volume for the two methods of manipulation and processing have been calculated. First one is sawing in accordance to schematics used in the sawmill of one of the largest producers of multilayer floorings in Europe. Second one is peripheral cutting with three diameters of peeler roll. Total loss volume for sawing was 55.8 ± 10.5% and for peripheral cutting with peeler roll with biggest chosen diameter of 100 mm was 45.6 ± 9.5%. Therefore, in presented case, peripheral cutting is more efficient than sawing.

Influence of machining technologies and quality of logs on material losses of typical supply of Scots pine wood (<italic>Pinus sylvestris</italic> L.) destined for layered floorboards

SGGW, Faculty of Wood Technology, Department of Wood Sciences and Wood Preservation

Folia Forestalia Polonica

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

Influence of machining technologies and quality of logs on material losses of typical supply of Scots pine wood ( L.) destined for layered floorboards

Pine wood is commonly used in the production of floorings and is mainly used for solid wood planks and as a base in multi-layer flooring material. From an...

Influence of machining technologies and quality of logs on material losses of typical supply of Scots pine wood (Pinus sylvestris L.) destined for layered floorboards

Pubblicato online: 25 gen 2019

Pagine: 241 - 247

Ricevuto: 23 nov 2017

Accettato: 15 nov 2018

DOI: https://doi.org/10.2478/ffp-2018-0025

Parole chiave
eccentricity, flattening, taper coefficient, heartwood fraction, multi-layer floorings, L., loss on sawing, loss on peripheral cutting

© 2018 Paweł Kozakiewicz et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

Influence of machining technologies and quality of logs on material losses of typical supply of Scots pine wood (Pinus sylvestris L.) destined for layered floorboards

Pubblicato online: 25 gen 2019

Pagine: 241 - 247

Ricevuto: 23 nov 2017

Accettato: 15 nov 2018

DOI: https://doi.org/10.2478/ffp-2018-0025

Parole chiaveeccentricity, flattening, taper coefficient, heartwood fraction, multi-layer floorings, L., loss on sawing, loss on peripheral cutting

© 2018 Paweł Kozakiewicz et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

Parole chiave
eccentricity, flattening, taper coefficient, heartwood fraction, multi-layer floorings, L., loss on sawing, loss on peripheral cutting