<abstract xmlns="http://www.w3.org/1999/xhtml">A continuous CO2 laser (10.6 µm wavelength) was adopted to investigate the influence of powder particle sizes on microstructural and morphological characteristics of laser claddings.To study the potential of powder in controlling the incident laser energy, different average particle sizes of Ni-base powder were deposited on an austenitic stainless steel X3CrNi18-10 substrate. The energy value necessary to melt a mass <italic>m</italic> of powder was calculated. The results indicate that this energy decreases with particle sizes.The claddings obtained with small particle sizes revealed a good morphological aspect and a low dilution of the cladding layer in the substrate, yet enough to create a very good metallurgical bond. The residual stress state was also influenced. Concerning modeling, we have elaborated residual stress model in the case of laser cladding by exploiting the response surface methodology (RSM), using a quadratic regression model. Combined effects of three laser cladding parameters on the residual stress is explored by a statistical analysis of variance (ANOVA). Results show that the residual stress is influenced principally by the power delivered by laser beam and by the scanning speed. It is also indicated that the size of powder particle is the dominant factor affecting the residual stress.</abstract>

A continuous CO2 laser (10.6 µm wavelength) was adopted to investigate the influence of powder particle sizes on microstructural and morphological characteristics of laser claddings.To study the potential of powder in controlling the incident laser energy, different average particle sizes of Ni-base powder were deposited on an austenitic stainless steel X3CrNi18-10 substrate. The energy value necessary to melt a mass m of powder was calculated. The results indicate that this energy decreases with particle sizes.The claddings obtained with small particle sizes revealed a good morphological aspect and a low dilution of the cladding layer in the substrate, yet enough to create a very good metallurgical bond. The residual stress state was also influenced. Concerning modeling, we have elaborated residual stress model in the case of laser cladding by exploiting the response surface methodology (RSM), using a quadratic regression model. Combined effects of three laser cladding parameters on the residual stress is explored by a statistical analysis of variance (ANOVA). Results show that the residual stress is influenced principally by the power delivered by laser beam and by the scanning speed. It is also indicated that the size of powder particle is the dominant factor affecting the residual stress.

Study of Powder Particle Size Effect on Microstructural and Geometrical Features of Laser Claddings Using Response Surface Methodology RSM

Department of Petrochemistry and Process Engineering, Faculty of Technology

Department of Mechanical Engineering, Faculty of Technology

Acta Universitatis Sapientiae, Electrical and Mechanical Engineering

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

A continuous CO2 laser (10.6 µm wavelength) was adopted to investigate the influence of powder particle sizes on microstructural and morphological...

Study of Powder Particle Size Effect on Microstructural and Geometrical Features of Laser Claddings Using Response Surface Methodology RSM

Pubblicato online: 31 dic 2019

Pagine: 99 - 116

Ricevuto: 22 set 2018

DOI: https://doi.org/10.2478/auseme-2019-0009

Parole chiave
Laser cladding, particle size, energy absorption, morphology, microstructure, RSM, ANOVA

© 2019 El Hadi Boussaha et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Study of Powder Particle Size Effect on Microstructural and Geometrical Features of Laser Claddings Using Response Surface Methodology RSM

Pubblicato online: 31 dic 2019

Pagine: 99 - 116

Ricevuto: 22 set 2018

DOI: https://doi.org/10.2478/auseme-2019-0009

Parole chiaveLaser cladding, particle size, energy absorption, morphology, microstructure, RSM, ANOVA

© 2019 El Hadi Boussaha et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Parole chiave
Laser cladding, particle size, energy absorption, morphology, microstructure, RSM, ANOVA