<abstract xmlns="http://www.w3.org/1999/xhtml">
<p>With the rapid development of the precision industry, aluminum alloy structural parts have been widely used. However, in the welding process of aluminum alloy, there are problems such as welding deformation and weld tumor defects due to the special physical characteristics of aluminum alloy. Therefore, this paper mainly focuses on 6063-T6 aluminum alloy as the research object to analyze the effect of the coating process on the organizational properties of MIG welded T-joints of 6063-T6 aluminum alloy. First, based on the Simufact welding finite element analysis platform, the establishment of a three-dimensional welding simulation model, the simulation calculations and test results for comparison, the peak temperature and temperature change trend of each measurement point between the two. Secondly, according to the T-joint welding process, welding numerical simulation of 6063-T6 aluminum alloy rear compartment structural parts to obtain the rear compartment assembly welding residual stress is mainly concentrated in the vicinity of the weld. Finally, the impact of welding current on the organization and properties of T-shaped welded joints of 6063-T6 aluminum alloy was discussed. The results show that the coating process has a good strengthening effect on the mechanical properties of welded joints. Compared with the pre-coating process, the welded joint tensile strength increased by 14.93%, and the welding coefficient of 73% of the parent material heat-affected zone microhardness increased by 21.82% compared to the pre-coating process. In this paper, the finite element theory of the coating process and MIG welding, T-joint organization between the found welding heat-affected zone after the coating process can make Mg, and Si atoms continue to be enriched, and mechanical properties strength is enhanced.</p>
</abstract>

With the rapid development of the precision industry, aluminum alloy structural parts have been widely used. However, in the welding process of aluminum alloy, there are problems such as welding deformation and weld tumor defects due to the special physical characteristics of aluminum alloy. Therefore, this paper mainly focuses on 6063-T6 aluminum alloy as the research object to analyze the effect of the coating process on the organizational properties of MIG welded T-joints of 6063-T6 aluminum alloy. First, based on the Simufact welding finite element analysis platform, the establishment of a three-dimensional welding simulation model, the simulation calculations and test results for comparison, the peak temperature and temperature change trend of each measurement point between the two. Secondly, according to the T-joint welding process, welding numerical simulation of 6063-T6 aluminum alloy rear compartment structural parts to obtain the rear compartment assembly welding residual stress is mainly concentrated in the vicinity of the weld. Finally, the impact of welding current on the organization and properties of T-shaped welded joints of 6063-T6 aluminum alloy was discussed. The results show that the coating process has a good strengthening effect on the mechanical properties of welded joints. Compared with the pre-coating process, the welded joint tensile strength increased by 14.93%, and the welding coefficient of 73% of the parent material heat-affected zone microhardness increased by 21.82% compared to the pre-coating process. In this paper, the finite element theory of the coating process and MIG welding, T-joint organization between the found welding heat-affected zone after the coating process can make Mg, and Si atoms continue to be enriched, and mechanical properties strength is enhanced.

Effect of post-welding coating process on the organization and properties of MIG-welded T-joints of 6063-T6 aluminum alloy

Applied Mathematics and Nonlinear Sciences

This work is licensed under the Creative Commons Attribution 4.0 International License.

With the rapid development of the precision industry, aluminum alloy structural parts have been widely used. However, in the welding process of aluminum alloy,...

Effect of post-welding coating process on the organization and properties of MIG-welded T-joints of 6063-T6 aluminum alloy

Pubblicato online: 01 ago 2023

Pagine: -

Ricevuto: 14 ott 2022

Accettato: 09 feb 2023

DOI: https://doi.org/10.2478/amns.2023.2.00123

Parole chiave
Aluminum alloy, Coating process, Joint organization, Simufact, Finite element

© 2023 Ximing Zhu, published by Sciendo

This work is licensed under the Creative Commons Attribution 4.0 International License.

Effect of post-welding coating process on the organization and properties of MIG-welded T-joints of 6063-T6 aluminum alloy

Pubblicato online: 01 ago 2023

Pagine: -

Ricevuto: 14 ott 2022

Accettato: 09 feb 2023

DOI: https://doi.org/10.2478/amns.2023.2.00123

Parole chiaveAluminum alloy, Coating process, Joint organization, Simufact, Finite element

© 2023 Ximing Zhu, published by Sciendo

This work is licensed under the Creative Commons Attribution 4.0 International License.

Parole chiave
Aluminum alloy, Coating process, Joint organization, Simufact, Finite element