<abstract xmlns="http://www.w3.org/1999/xhtml">Numerical simulations with the COREDIV code of JET H-mode discharges with 25 MW of auxiliary heating in the ITER-like wall (ILW) configuration with different impurity seedings – nitrogen (N), neon (Ne), argon (Ar) and krypton (Kr) – are presented. All simulations have been performed with the same transport model and input discharge parameters like auxiliary heating, volume average plasma density, confinement factor. Only the seeded impurity puff rate was changed in the calculations. It appears that for the considered heating power of 25 MW and relatively low volume electron average density &lt;<italic>n</italic>e> = 6.2 × 1019 m−3, impurity seeding is necessary. It has been found that for every gas at the maximum level of the seeding rate, allowed by the code convergence, the power to the plate is reduced up to 2–4 MW, with electron temperature at the plate of about 2 eV, indicating semi-detached conditions in the divertor region. It should be noted, however, that in cases with low and medium <italic>Z</italic> impurity (N, Ne and Ar), tungsten radiation is a significant part of radiation losses and stays above 22–32% of the total energy losses, but for high <italic>Z</italic> impurity (Kr) it is reduced up to 10% of the total losses. The maximum of the Kr radiation is between the pedestal region and separatrix, showing that radiative mantle can be created, which might have a strong influence on the plasma parameters in the pedestal region.</abstract>

Numerical simulations with the COREDIV code of JET H-mode discharges with 25 MW of auxiliary heating in the ITER-like wall (ILW) configuration with different impurity seedings – nitrogen (N), neon (Ne), argon (Ar) and krypton (Kr) – are presented. All simulations have been performed with the same transport model and input discharge parameters like auxiliary heating, volume average plasma density, confinement factor. Only the seeded impurity puff rate was changed in the calculations. It appears that for the considered heating power of 25 MW and relatively low volume electron average density <ne> = 6.2 × 1019 m−3, impurity seeding is necessary. It has been found that for every gas at the maximum level of the seeding rate, allowed by the code convergence, the power to the plate is reduced up to 2–4 MW, with electron temperature at the plate of about 2 eV, indicating semi-detached conditions in the divertor region. It should be noted, however, that in cases with low and medium Z impurity (N, Ne and Ar), tungsten radiation is a significant part of radiation losses and stays above 22–32% of the total energy losses, but for high Z impurity (Kr) it is reduced up to 10% of the total losses. The maximum of the Kr radiation is between the pedestal region and separatrix, showing that radiative mantle can be created, which might have a strong influence on the plasma parameters in the pedestal region.

COREDIV modelling of JET ILW discharges with different impurity seeding: nitrogen, neon, argon and krypton

Nukleonika

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Numerical simulations with the COREDIV code of JET H-mode discharges with 25 MW of auxiliary heating in the ITER-like wall (ILW) configuration with different impurity seedings – nitrogen (N), neon (Ne), argon (Ar) and krypton (Kr) – are presented. All simulations have been performed with the same transport model and input discharge parameters like auxiliary heating, volume average plasma density, confinement factor. Only the seeded impurity puff rate was changed in the calculations. It appears that for the considered heating power of 25 MW and relatively low volume electron average density  = 6.2 × 1019 m−3, impurity seeding is necessary. It has been found that for every gas at the maximum level of the seeding rate, allowed by the code convergence, the power to the plate is reduced up to 2–4 MW, with electron temperature at the plate of about 2 eV, indicating semi-detached conditions in the divertor region. It should be noted, however, that in cases with low and medium Z impurity (N, Ne and Ar), tungsten radiation is a significant part of radiation losses and stays above 22–32% of the total energy losses, but for high Z impurity (Kr) it is reduced up to 10% of the total losses. The maximum of the Kr radiation is between the pedestal region and separatrix, showing that radiative mantle can be created, which might have a strong influence on the plasma parameters in the pedestal region.

Numerical simulations with the COREDIV code of JET H-mode discharges with 25 MW of auxiliary heating in the ITER-like wall (ILW) configuration with different...

COREDIV modelling of JET ILW discharges with different impurity seeding: nitrogen, neon, argon and krypton

Pubblicato online: 04 mar 2017

Pagine: 3 - 7

Ricevuto: 09 giu 2016

Accettato: 12 nov 2016

DOI: https://doi.org/10.1515/nuka-2017-0001

Parole chiave
impurity seeding, integrated modelling, tokamak

© 2017 Irena Ivanova-Stanik et al., published by De Gruyter Open

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

COREDIV modelling of JET ILW discharges with different impurity seeding: nitrogen, neon, argon and krypton

Pubblicato online: 04 mar 2017

Pagine: 3 - 7

Ricevuto: 09 giu 2016

Accettato: 12 nov 2016

DOI: https://doi.org/10.1515/nuka-2017-0001

Parole chiaveimpurity seeding, integrated modelling, tokamak

© 2017 Irena Ivanova-Stanik et al., published by De Gruyter Open

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Parole chiave
impurity seeding, integrated modelling, tokamak