[1. Becker A.A. (1992), The boundary element method in engineering, McGraw – Hill International, New York.]Search in Google Scholar
[2. Brighenti R., Carpinteri A., Vantadori S. (2012), Fatigue life assessment under a comlpex multiaxial load history: an approach based on damage mechanics, Fatigue & Fracture of Engineering Materials & Structures, Vol. 35, 141-153.]Search in Google Scholar
[3. Derpeński Ł., Seweryn A. (2007), Numerical analysis of fracture for specimens with notches made of elasto-plastic material, Acta Mechanica et Automatica, Vol. 1 (1), 27-30 (in Polish).]Search in Google Scholar
[4. Döring R., Hoffmeyer J., Seeger T., Vormwald M. (2006), Short fatigue crack growth nonproportional multiaxial elastic-plastic strains, International Journal of Fatigue, Vol. 28 (9), 972-982.]Search in Google Scholar
[5. Duchaczek A., Mańko Z. (2012), Assessment of direct method of calculating stress intensity factor, Journal of Science of the gen. Tadeusz Kosciuszko Military Academy of Land Forces, No. 3 (165), 336-346 (in Polish).10.5604/01.3001.0002.3510]Search in Google Scholar
[6. Faszynka S., Rozumek D. (2014), Application of the FRANC3D software for crack growth calculations, Mechanik, No. 11, 932-934 (in Polish).]Search in Google Scholar
[7. Faszynka S., Rozumek D., Lewandowski J. (2015), Crack growth path in specimens with rectangular section under bending with torsion, Solid State Phenomena, Vol. 224, 133-138.]Search in Google Scholar
[8. Kleiber M. (1995), Computational methods in mechanics of solids, Warsaw, PWN (in Polish).]Search in Google Scholar
[9. Rozumek D., Hepner M., Faszynka S. (2015), Fatigue tests of PA6 and PA7 alloys subjected to bending without and after precipitation hardening, Mechanik, No. 3, 246-249 (in Polish).10.17814/mechanik.2015.3.103]Search in Google Scholar
[10. Rozumek D., Macha E. (2006), Elastic-plastic fatigue crack growth in 18G2A steel under proportional bending with torsion loading, Fatigue & Fracture of Engineering Materials & Structures, Vol. 29 (2), 135-145.]Search in Google Scholar
[11. Rozumek D., Macha E.(2009), J-integral in the description of fatigue crack growth rate induced by different ratios of torsion to bending loading in AlCu4Mg1, Mat.-wiss. u. Werkstofftech., Vol. 40 (10), 743-749.10.1002/mawe.200900501]Search in Google Scholar
[12. Rusiński E. (2002), Design principles supporting structures of motor vehicles, Oficyna Wydawnicza PolitechnikiWrocławskiej, Wrocław (in Polish).]Search in Google Scholar
[13. Seweryn A., (2002), Modeling of singular stress fields using finite element method, Int. Journal of Solids and Structures, Vol. 39 (18), 4787-4804.10.1016/S0020-7683(02)00371-2]Search in Google Scholar
[14. Susmel L., Taylor D. (2007), Non-propagating cracks and high-cycle fatigue failures in sharply notched specimens under in-phase Mode I and II loading, Engineering Failure Analysis, Vol. 14, 861-876.]Search in Google Scholar
[15. Szusta J., Seweryn A. (2010), Fatigue damage accumulation modelling in the range of complex low-cycle loadings – The strain appoach and its experimental verification on the basis of EN AW-2007 aluminium alloy, International Journal of Fatigue, Vol. 33 (2), 255-264.]Search in Google Scholar
[16. Thum A., Petersen C., Swenson O. (1960), Deformation, stress and notch effect, VDI, Duesseldorf (in German).]Search in Google Scholar
[17. Zappalorto M., Berto F., Lazzarin P. (2011), Practical expressions for the notch stress concentration factors of round bars under torsion, International Journal of Fatigue, Vol. 33 (3), 382-395.]Search in Google Scholar
[18. Zienkiewicz O. C., Taylor R. L. (2000), The finite element method, Butterworth Heinemann, Vol. 1-3, Oxford.]Search in Google Scholar
[19.www.cfg.cornell.edu/software/software.htm.]Search in Google Scholar
