<abstract xmlns="http://www.w3.org/1999/xhtml"><p>Al-Li alloys are used in various industries owing to their good mechanical and physical properties. However, one of the limiting factors of welding the aluminium alloys by laser beam is the high reflectivity of the beam and thus the reduced efficiency of the laser. Reduction of reflectivity can be achieved by increasing the surface roughness, which may have a beneficial effect on the absorption of the laser, resulting into affecting the weld bead dimensions. The paper deals with the analysis of the influence of surface roughness of welded materials on geometry of welded joints. Specimens of AW 2099 alloy 2099 with a thickness of 3 mm were milled to achieve different levels of roughness, and then laser welded. Characteristic dimensions of the welds (weld surface/root width) were measured. The obtained data were statistically analysed using the ANOVA method, in order to assess statistical significance of the influence of individual roughness parameters on the geometric characteristics of welds. The results of the analysis showed that, within the monitored range and surface roughness parameters, only the influence of roughness parameter Rq, Rz on the weld root width can be considered statistically significant.</p></abstract>

Al-Li alloys are used in various industries owing to their good mechanical and physical properties. However, one of the limiting factors of welding the aluminium alloys by laser beam is the high reflectivity of the beam and thus the reduced efficiency of the laser. Reduction of reflectivity can be achieved by increasing the surface roughness, which may have a beneficial effect on the absorption of the laser, resulting into affecting the weld bead dimensions. The paper deals with the analysis of the influence of surface roughness of welded materials on geometry of welded joints. Specimens of AW 2099 alloy 2099 with a thickness of 3 mm were milled to achieve different levels of roughness, and then laser welded. Characteristic dimensions of the welds (weld surface/root width) were measured. The obtained data were statistically analysed using the ANOVA method, in order to assess statistical significance of the influence of individual roughness parameters on the geometric characteristics of welds. The results of the analysis showed that, within the monitored range and surface roughness parameters, only the influence of roughness parameter Rq, Rz on the weld root width can be considered statistically significant.

Influence of Surface Roughness on Selected Geometric Characteristics of Laser Beam Welded Joints of AW 2099 Alloy

Research Papers Faculty of Materials Science and Technology Slovak University of Technology

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Al-Li alloys are used in various industries owing to their good mechanical and physical properties. However, one of the limiting factors of welding the...

Influence of Surface Roughness on Selected Geometric Characteristics of Laser Beam Welded Joints of AW 2099 Alloy

Publié en ligne: 12 déc. 2020

Pages: 56 - 64

Reçu: 26 août 2020

Accepté: 26 oct. 2020

DOI: https://doi.org/10.2478/rput-2020-0019

Mots clés
Laser welding, AW 2099, geometric characteristics, ANOVA

© 2020 Filip Šugra et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Influence of Surface Roughness on Selected Geometric Characteristics of Laser Beam Welded Joints of AW 2099 Alloy

Publié en ligne: 12 déc. 2020

Pages: 56 - 64

Reçu: 26 août 2020

Accepté: 26 oct. 2020

DOI: https://doi.org/10.2478/rput-2020-0019

Mots clésLaser welding, AW 2099, geometric characteristics, ANOVA

© 2020 Filip Šugra et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Mots clés
Laser welding, AW 2099, geometric characteristics, ANOVA