<abstract xmlns="http://www.w3.org/1999/xhtml">According to the new European Union Basic Safety Standards (EU-BSS), preparation of the National Radon Action Plan is obligatory for the Member States. One of the plan’s aims is to carry out an indoor radon survey to identify radon-prone areas. In the radon surveys, track detector methods are used. At the University of Pannonia (Veszprém, Hungary), a new scanner-based detector evaluation system has been developed. For the application of the new system, the selection of appropriate parameters is necessary. In this study, selection of the applied track detectors and setting of the etching conditions have been carried out. Two different types of allyl diglycol carbonate (ADC or CR-39) track detectors were investigated, taking into account the detector’s background and response during the exposure (determination of calibration factor). The Baryotrak’s background track density (0–1.5 tracks mm−2) was lower than that of the 0.8–4 tracks mm−2. The response of the Tastrak was higher, but the deviation of the calibration factor was much higher (1.2–5.3 × 10−3 tracks mm−2/(Bq day m−3)) than in the case of the Baryotrak (1.4–2.8 × 10−3 tracks mm−2/(Bq day m−3)). After the systematic review of the etching system, a new method was developed. For the determination of the optimal track diameter, the argon fluoride (ArF) laser was applied to create tracks with diameters in the range of 10–100 μm. The optimum track size was in the range of 40–60 μm. On this basis, new etching conditions were determined: 6.25 M NaOH solution, a temperature of 90°C, and time period of 8 hours.</abstract>

According to the new European Union Basic Safety Standards (EU-BSS), preparation of the National Radon Action Plan is obligatory for the Member States. One of the plan’s aims is to carry out an indoor radon survey to identify radon-prone areas. In the radon surveys, track detector methods are used. At the University of Pannonia (Veszprém, Hungary), a new scanner-based detector evaluation system has been developed. For the application of the new system, the selection of appropriate parameters is necessary. In this study, selection of the applied track detectors and setting of the etching conditions have been carried out. Two different types of allyl diglycol carbonate (ADC or CR-39) track detectors were investigated, taking into account the detector’s background and response during the exposure (determination of calibration factor). The Baryotrak’s background track density (0–1.5 tracks mm−2) was lower than that of the 0.8–4 tracks mm−2. The response of the Tastrak was higher, but the deviation of the calibration factor was much higher (1.2–5.3 × 10−3 tracks mm−2/(Bq day m−3)) than in the case of the Baryotrak (1.4–2.8 × 10−3 tracks mm−2/(Bq day m−3)). After the systematic review of the etching system, a new method was developed. For the determination of the optimal track diameter, the argon fluoride (ArF) laser was applied to create tracks with diameters in the range of 10–100 μm. The optimum track size was in the range of 40–60 μm. On this basis, new etching conditions were determined: 6.25 M NaOH solution, a temperature of 90°C, and time period of 8 hours.

Configuration of the parameters for scanner-based track detector evaluation system

Nukleonika

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

According to the new European Union Basic Safety Standards (EU-BSS), preparation of the National Radon Action Plan is obligatory for the Member States. One of...

Configuration of the parameters for scanner-based track detector evaluation system

Publié en ligne: 29 mai 2020

Pages: 133 - 137

Reçu: 02 déc. 2019

Accepté: 06 févr. 2020

DOI: https://doi.org/10.2478/nuka-2020-0021

Mots clés
Background track density, CR-39, Etching conditions, Indoor radon, Sensitivity for radon

© 2020 Anita Csordás et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

Configuration of the parameters for scanner-based track detector evaluation system

Publié en ligne: 29 mai 2020

Pages: 133 - 137

Reçu: 02 déc. 2019

Accepté: 06 févr. 2020

DOI: https://doi.org/10.2478/nuka-2020-0021

Mots clésBackground track density, CR-39, Etching conditions, Indoor radon, Sensitivity for radon

© 2020 Anita Csordás et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

Mots clés
Background track density, CR-39, Etching conditions, Indoor radon, Sensitivity for radon