<abstract xmlns="http://www.w3.org/1999/xhtml"><p>The purpose of this work is to achieve the best efficiency of Cu(In, Ga)Se2 solar cells by replacing the CdS buffer layer with other nontoxic materials. The simulation tool used in this study is Silvaco-Atlas package based on digital resolution 2D transport equations governing the conduction mechanisms in semiconductor devices. The J-V characteristics are simulated under AM1.5G illumination. Firstly, we will report the modeling and simulation results of CdS/CIGS solar cell, in comparison with the previously reported experimental results [1]. Secondly, the photovoltaic parameters will be calculated with CdS buffer layer and without any buffer layer to understand its impact on the output parameters of solar cells. The simulation is carried out with the use of electrical and optical parameters chosen judiciously for different buffers (CdS, ZnOS and ZnSe). In comparison to simulated CdS/CIGS, the best photovoltaic parameters have been obtained with ZnOS buffer layer. The structure has almost the same open circuit voltage Voc and fill factor FF, and higher short circuit current density Jsc, which results in slightly higher conversion efficiencies.</p></abstract>

The purpose of this work is to achieve the best efficiency of Cu(In, Ga)Se2 solar cells by replacing the CdS buffer layer with other nontoxic materials. The simulation tool used in this study is Silvaco-Atlas package based on digital resolution 2D transport equations governing the conduction mechanisms in semiconductor devices. The J-V characteristics are simulated under AM1.5G illumination. Firstly, we will report the modeling and simulation results of CdS/CIGS solar cell, in comparison with the previously reported experimental results [1]. Secondly, the photovoltaic parameters will be calculated with CdS buffer layer and without any buffer layer to understand its impact on the output parameters of solar cells. The simulation is carried out with the use of electrical and optical parameters chosen judiciously for different buffers (CdS, ZnOS and ZnSe). In comparison to simulated CdS/CIGS, the best photovoltaic parameters have been obtained with ZnOS buffer layer. The structure has almost the same open circuit voltage Voc and fill factor FF, and higher short circuit current density Jsc, which results in slightly higher conversion efficiencies.

Investigation of Cu(In, Ga)Se2 solar cell performance with non-cadmium buffer layer using TCAD-SILVACO

Applied Microelectronic Laboratory, Faculty of Electrical Engineering

Djillali Liabes University of Sidi Bel Abbes

Materials Science-Poland

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

The purpose of this work is to achieve the best efficiency of Cu(In, Ga)Se2 solar cells by replacing the CdS buffer layer with other nontoxic materials. The...

Investigation of Cu(In, Ga)Se2 solar cell performance with non-cadmium buffer layer using TCAD-SILVACO

Publié en ligne: 02 nov. 2018

Pages: 514 - 519

Reçu: 13 déc. 2017

Accepté: 26 avr. 2018

DOI: https://doi.org/10.2478/msp-2018-0054

Mots clés
CIGS, ZnS, ZnOS, ZnSe, Atlas-SILVACO

© 2018 Bechlaghem Sara et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

Investigation of Cu(In, Ga)Se2 solar cell performance with non-cadmium buffer layer using TCAD-SILVACO

Publié en ligne: 02 nov. 2018

Pages: 514 - 519

Reçu: 13 déc. 2017

Accepté: 26 avr. 2018

DOI: https://doi.org/10.2478/msp-2018-0054

Mots clésCIGS, ZnS, ZnOS, ZnSe, Atlas-SILVACO

© 2018 Bechlaghem Sara et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

Mots clés
CIGS, ZnS, ZnOS, ZnSe, Atlas-SILVACO