<abstract xmlns="http://www.w3.org/1999/xhtml"><p>The design and implementation of planar multi-way differential power dividers remain a challenge in terms of the compactness and especially, for the achievable characteristic impedance of the quarter-wavelength transformer when considering large number of outputs. In this work, the double-sided parallel stripline is recommended to realize such a power divider with out-of-phase outputs, and explicit design methods are provided. The proposed multi-way power divider was developed without the use of lump elements on a single substrate. For system applications, a prototype operating at 41.6 MHz with 12 pairs of out-of-phase outputs that utilize the microstrip line as the output interfaces was fabricated and examined. At the center frequency of 41.6MHz, the developed prototype measured insertion losses akin to 14.3 dB as compared with the theoretical data of 13.8 dB. The attainable impedance bandwidth ranges from 10 MHz to 80 MHz under a magnitude imbalance of ±0.3 dB. The isolations of the adjacent outputs are about 13.1 dB as compared with the theoretical values of 14.428 dB, and are better than 34 dB for more distant ones. Parameter measurements are in good agreement with the numerical predications, thus demonstrating the realization of the proposed multi-way power divider.</p></abstract>

The design and implementation of planar multi-way differential power dividers remain a challenge in terms of the compactness and especially, for the achievable characteristic impedance of the quarter-wavelength transformer when considering large number of outputs. In this work, the double-sided parallel stripline is recommended to realize such a power divider with out-of-phase outputs, and explicit design methods are provided. The proposed multi-way power divider was developed without the use of lump elements on a single substrate. For system applications, a prototype operating at 41.6 MHz with 12 pairs of out-of-phase outputs that utilize the microstrip line as the output interfaces was fabricated and examined. At the center frequency of 41.6MHz, the developed prototype measured insertion losses akin to 14.3 dB as compared with the theoretical data of 13.8 dB. The attainable impedance bandwidth ranges from 10 MHz to 80 MHz under a magnitude imbalance of ±0.3 dB. The isolations of the adjacent outputs are about 13.1 dB as compared with the theoretical values of 14.428 dB, and are better than 34 dB for more distant ones. Parameter measurements are in good agreement with the numerical predications, thus demonstrating the realization of the proposed multi-way power divider.

Multi-way differential power divider with microstrip output interfaces

Tianjin University of Technology and Education

University of Electronic Science and Technology of China (UESTC)

Electrical and Electronic Engineering Department

Journal of Electrical Engineering

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

{"article-title":"Multi-way differential power divider with microstrip output interfaces"}

The design and implementation of planar multi-way differential power dividers remain a challenge in terms of the compactness and especially, for the achievable...

Multi-way differential power divider with microstrip output interfaces

Publié en ligne: 22 sept. 2020

Pages: 274 - 280

Reçu: 09 mai 2020

DOI: https://doi.org/10.2478/jee-2020-0037

Mots clés
power divider, multi-way, differential, microstrip

© 2020 Cheng-Guang Sun et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Multi-way differential power divider with microstrip output interfaces

Publié en ligne: 22 sept. 2020

Pages: 274 - 280

Reçu: 09 mai 2020

DOI: https://doi.org/10.2478/jee-2020-0037

Mots cléspower divider, multi-way, differential, microstrip

© 2020 Cheng-Guang Sun et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Mots clés
power divider, multi-way, differential, microstrip