<abstract xmlns="http://www.w3.org/1999/xhtml">

<p>With the development of the embedded system and improvement of the requirements from customers, embedded GUI which was used to communicate between users and embedded system became to be a key in researching the embedded system. This article introduced what is embedded system and what is embedded GUI. It described the porting of an embedded GUI on ARM Linux platform, including the establishment of compile environment, configuring and modifying of compile options and setting of runtime parameters. Above all, this article introduces the development of Embedded Linux GUI, describes the GUI development environment of Qt /Embedded and Qt, one procedure of the app location development based on Qt/Embedded is described in detail. This system adopts the B/S mode and uses the ARM11 development board with S3C6410 as the core. Sensors are used to obtain information, and the obtained data is judged and analyzed. When the preset conditions are not met, an alarm function is triggered. At the same time, data transmission is carried out through the Zigbee wireless module, and the receiving end analyzes and displays the received data. Each device is connected to the Zigbee module, which distinguishes it by assigning different network addresses and constantly transmits the status of the monitoring area to the receiving end. The receiving end distinguishes the monitoring status of different locations based on the different network addresses, increasing mobility.</p>
</abstract>

With the development of the embedded system and improvement of the requirements from customers, embedded GUI which was used to communicate between users and embedded system became to be a key in researching the embedded system. This article introduced what is embedded system and what is embedded GUI. It described the porting of an embedded GUI on ARM Linux platform, including the establishment of compile environment, configuring and modifying of compile options and setting of runtime parameters. Above all, this article introduces the development of Embedded Linux GUI, describes the GUI development environment of Qt /Embedded and Qt, one procedure of the app location development based on Qt/Embedded is described in detail. This system adopts the B/S mode and uses the ARM11 development board with S3C6410 as the core. Sensors are used to obtain information, and the obtained data is judged and analyzed. When the preset conditions are not met, an alarm function is triggered. At the same time, data transmission is carried out through the Zigbee wireless module, and the receiving end analyzes and displays the received data. Each device is connected to the Zigbee module, which distinguishes it by assigning different network addresses and constantly transmits the status of the monitoring area to the receiving end. The receiving end distinguishes the monitoring status of different locations based on the different network addresses, increasing mobility.

Fabrication and Development of the Embedded Linux Based on the ARM System

Xi'an University of Posts and Telecommunications

International Journal of Advanced Network, Monitoring and Controls

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

{"article-title":"Fabrication and Development of the Embedded Linux Based on the ARM System"}

With the development of the embedded system and improvement of the requirements from customers, embedded GUI which was used to communicate between users and...

Fabrication and Development of the Embedded Linux Based on the ARM System

Publié en ligne: 21 juil. 2024

Pages: 82 - 88

DOI: https://doi.org/10.2478/ijanmc-2024-0018

Mots clés
Virtual System, Embedded System, GUI, Porting, Qt, Qt/Embedded

© 2024 Ruoyu Wang et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Fabrication and Development of the Embedded Linux Based on the ARM System

Publié en ligne: 21 juil. 2024

Pages: 82 - 88

DOI: https://doi.org/10.2478/ijanmc-2024-0018

Mots clésVirtual System, Embedded System, GUI, Porting, Qt, Qt/Embedded

© 2024 Ruoyu Wang et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Mots clés
Virtual System, Embedded System, GUI, Porting, Qt, Qt/Embedded