<abstract xmlns="http://www.w3.org/1999/xhtml"><p>Nowadays, the concrete is the most widely used composite material among those made by human and the second (after water) among all materials used by people. It is an ecological material, being made of local raw materials – aggregate, cement, water, admixtures and mineral additives − characterized by the lowest carbon trace. The paper presents results of investigations of the concretes of C20/25 class based on the cement CEM I 42.5R, pebble aggregate as well as fly ashes from thermal conversion of sewage sludge replacing 5, 10, 15 and 20% of the cement mass. In the course of experimental work, compressive strength measurements were made at two stages of curing and frost resistance F150. The collected research results made it possible to compare the properties of concretes produced with the ash from two treatment plants. The obtained results confirm possibility of manufacturing of the concretes modified by fly ash from combustion of municipal sewage sludge. The average compressive strength for the concrete containing 20% of ash from Kraków has been established at the level of 50.1 and 50.6 MPa after 28 and 56 days of curing, respectively and for ash from Warsaw at 42.6 and 45.7 MPa.</p></abstract>

Nowadays, the concrete is the most widely used composite material among those made by human and the second (after water) among all materials used by people. It is an ecological material, being made of local raw materials – aggregate, cement, water, admixtures and mineral additives − characterized by the lowest carbon trace. The paper presents results of investigations of the concretes of C20/25 class based on the cement CEM I 42.5R, pebble aggregate as well as fly ashes from thermal conversion of sewage sludge replacing 5, 10, 15 and 20% of the cement mass. In the course of experimental work, compressive strength measurements were made at two stages of curing and frost resistance F150. The collected research results made it possible to compare the properties of concretes produced with the ash from two treatment plants. The obtained results confirm possibility of manufacturing of the concretes modified by fly ash from combustion of municipal sewage sludge. The average compressive strength for the concrete containing 20% of ash from Kraków has been established at the level of 50.1 and 50.6 MPa after 28 and 56 days of curing, respectively and for ash from Warsaw at 42.6 and 45.7 MPa.

Influence of Flight Ash Properties from Thermal Transformation of Sewage Sludge on Ordinary Concrete Parameters

National University of Water and Environmental Engineering in Rivne

Acta Scientiarum Polonorum Architectura

This work is licensed under the Creative Commons Attribution-NonCommercial 4.0 International License.

Nowadays, the concrete is the most widely used composite material among those made by human and the second (after water) among all materials used by people. It...

Influence of Flight Ash Properties from Thermal Transformation of Sewage Sludge on Ordinary Concrete Parameters

Publié en ligne: 29 janv. 2021

Pages: 43 - 54

Reçu: 10 sept. 2020

Accepté: 25 sept. 2020

DOI: https://doi.org/10.22630/aspa.2020.19.3.26

Mots clés
concrete, fly ash, concrete, properties of concrete

© 2020 Gabriela Rutkowska et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial 4.0 International License.

Influence of Flight Ash Properties from Thermal Transformation of Sewage Sludge on Ordinary Concrete Parameters

Publié en ligne: 29 janv. 2021

Pages: 43 - 54

Reçu: 10 sept. 2020

Accepté: 25 sept. 2020

DOI: https://doi.org/10.22630/aspa.2020.19.3.26

Mots clésconcrete, fly ash, concrete, properties of concrete

© 2020 Gabriela Rutkowska et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial 4.0 International License.

Mots clés
concrete, fly ash, concrete, properties of concrete