<abstract xmlns="http://www.w3.org/1999/xhtml"><p>Eucalyptus fibers were modified with N-β(aminoethyl)-γ-aminopropyl trimethoxy silane to research the fiber surface’s changes and the influence of the treatment on the mechanical properties, flame resistance, thermal conductivity and microstructure of eucalyptus fiber composite phenolic foams (EFCPFs). The results showed that the partial of hemicelluloses, waxes, lignin and impurities from the fiber surface were dissolved and removed. Compared with untreated EFCPFs, the mechanical properties of treated EFCPFs were increased dramatically; The size of cells was smaller and the distribution was more uniform; The thermal conductivities were basically reduced; Especially the ratio of mass loss decreased obviously. However limited oxygen indexs (LOIs) reduced. And the mechanical properties and LOIs of EFCPFs were basically decreased with the increase of eucalyptus fibers. By comprehensive analysis, the results showed that the interfacial compatibility has been significantly improved between eucalyptus fibers and phenolic resin. And the suitable dosage of eucalyptus fibers was about 5%.</p></abstract>

Eucalyptus fibers were modified with N-β(aminoethyl)-γ-aminopropyl trimethoxy silane to research the fiber surface’s changes and the influence of the treatment on the mechanical properties, flame resistance, thermal conductivity and microstructure of eucalyptus fiber composite phenolic foams (EFCPFs). The results showed that the partial of hemicelluloses, waxes, lignin and impurities from the fiber surface were dissolved and removed. Compared with untreated EFCPFs, the mechanical properties of treated EFCPFs were increased dramatically; The size of cells was smaller and the distribution was more uniform; The thermal conductivities were basically reduced; Especially the ratio of mass loss decreased obviously. However limited oxygen indexs (LOIs) reduced. And the mechanical properties and LOIs of EFCPFs were basically decreased with the increase of eucalyptus fibers. By comprehensive analysis, the results showed that the interfacial compatibility has been significantly improved between eucalyptus fibers and phenolic resin. And the suitable dosage of eucalyptus fibers was about 5%.

The structure and properties of eucalyptus fiber/phenolic foam composites under N-β(aminoethyl)-<italic>γ</italic>-aminopropyl trimethoxy silane pretreatments

College of Materials Science and Engineering

Institute of Chemical Industry of Forestry Products

Polish Journal of Chemical Technology

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

The structure and properties of eucalyptus fiber/phenolic foam composites under N-β(aminoethyl)--aminopropyl trimethoxy silane pretreatments

Eucalyptus fibers were modified with N-β(aminoethyl)-γ-aminopropyl trimethoxy silane to research the fiber surface’s changes and the influence of the treatment...

The structure and properties of eucalyptus fiber/phenolic foam composites under N-β(aminoethyl)-γ-aminopropyl trimethoxy silane pretreatments

Publié en ligne: 29 déc. 2017

Pages: 116 - 121

DOI: https://doi.org/10.1515/pjct-2017-0077

Mots clés
eucalyptus fiber, pheonlic foam, N-β(aminoethyl)-γ-aminopropyl trimethoxy silane, surface modification, composites

© 2017 Yufeng Ma et al., published by De Gruyter Open

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

The structure and properties of eucalyptus fiber/phenolic foam composites under N-β(aminoethyl)-γ-aminopropyl trimethoxy silane pretreatments

Publié en ligne: 29 déc. 2017

Pages: 116 - 121

DOI: https://doi.org/10.1515/pjct-2017-0077

Mots cléseucalyptus fiber, pheonlic foam, N-β(aminoethyl)-γ-aminopropyl trimethoxy silane, surface modification, composites

© 2017 Yufeng Ma et al., published by De Gruyter Open

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Mots clés
eucalyptus fiber, pheonlic foam, N-β(aminoethyl)-γ-aminopropyl trimethoxy silane, surface modification, composites