<abstract xmlns="http://www.w3.org/1999/xhtml"> This work presents the preparation of coatings of aluminium and AlCr6Fe2 alloy on magnesium alloy AZ91 with metallurgical bonding. Coatings were prepared by plasma spraying system WSP®-H 500. This metallurgical bond (sub-layer) is formed by an eutectic structure consisting of the intermetallic phase Mg17Al12 and the solid solution of magnesium and aluminium. In this work, the layers were studied using electrochemical impedance spectroscopy (EIS). It was shown that there is a several fold increase of the polarization resistance (Rcν) of plasma-sprayed coatings of aluminium and AlCr6Fe2 alloy, compared with uncoated AZ91 in borate buffer with pH 9.1.</abstract>

EIS and corrosion behaviour of plasma sprayed layers of Al and AlCr6Fe2 on AZ91

<abstract xmlns="http://www.w3.org/1999/xhtml"> The actual industrial trend is focused on weight reduction of constructions while preserving strength properties. For this purpose, conventional steel are replaced by high strength steels.. The aim of this study was to evaluate the effects of mechanical surface pre-treatment on corrosion resistance of high strength low alloy steel Domex 700 before and after surface treatment by manganese phosphating. Tested environment was 0,1M NaCl solution. Evaluation of mechanical pre-treatment and phosphating effects on corrosion resistance was realized by electrochemical measurements: potentiodynamic polarization measurements (Tafel analysis) and electrochemical impedance spectroscopy (equivalent circuits). From resulsts it is possible to conclude, that creation of manganese phosphate layer on ground and shot peened steel surface significantly increases the corrosion resistance of Domex 700 steel.</abstract>

Effect of combined surface treatment on quality and electrochemical corrosion properties of manganese phosphate on hsla steel domex 700

<abstract xmlns="http://www.w3.org/1999/xhtml"> This article was focused on the evaluation of neutral salt spray test effect (according to ISO 9124), procedure E4, on mechanical properties of load-bearing adhesive joints. The study also comprises the influence of substrate material (mild steel, aluminum alloys) and substrate surface roughness (verified by optical confocal microscopy). The experimental program contained acrylate-based adhesive and hybrid silicone polyurethane based adhesive which were applied in double lap joints loaded by shear.</abstract>

Influence of the adhesive type and metal substrate on adhesion of bonded joints after salt spray test

<abstract xmlns="http://www.w3.org/1999/xhtml"> There have been revealed and summarized the regularities in biocorrosion of steel 17G1S-U, which is traditionally used for manufacturing oil and gas mains. The basic regularities of biocorrosion processes in the 17G1S-U pipe steel under the influence of SRB Desulfovibrio Sp. strains Kyiv-10 was obtained by weight-loss testing and surface analysis techniques. Effective inhibitors are proposed, which allow protecting steel 17G1S-U against the development of anaerobic corrosion under the influence of sulfate-reducing bacteria (SRB). The effectiveness of inhibitors is estimated by the degree of their protective effect. The porous structure of the surface film contributes to the initiation of localized corrosion. Damage analysis of the specimen surface corroded under different test conditions was performed.</abstract>

Influence of soil microorganisms on metal corrosion of underground pipelines

<abstract xmlns="http://www.w3.org/1999/xhtml"> Copper is widely used metal for industrial and public purposes due to its good corrosion resistance and excellent electrical conductivity. In indoor atmospheric environments with low level of air pollution the corrosion rate of copper is very low and it is not affected by slight increasing of temperature or relative humidity. In many indoor environment hydrogen sulphide (H2S) occurs and significantly affects the copper corrosion. CuS is a loose of black corrosion product which can’t form protective film on copper surface and promote corrosion by adsorption of moisture as carrier. In sulphide presence, the corrosion product is chalcocite Cu2S. Copper corrosion attack by H2S low concentration caused significant failure of electronic, electric equipment but also other copper parts as tubes, etc. These corrosion films can form an insulating layer on the contact surfaces causing electrical failures on the electronic devices.</abstract>

Failure of electric products by H2S

AHEAD OF PRINT

Volume 68 (2024): Issue 1 (March 2024)

Volume 67 (2023): Issue 1 (May 2023)

Volume 66 (2022): Issue 1 (January 2022)

Volume 65 (2021): Issue 4 (December 2021)

Volume 65 (2021): Issue 3 (November 2021)

Volume 65 (2021): Issue 2 (September 2021)

Volume 65 (2021): Issue 1 (May 2021)

Volume 64 (2020): Issue 4 (December 2020)

Volume 64 (2020): Issue 3 (October 2020)

Volume 64 (2020): Issue 2 (June 2020)

Volume 64 (2020): Issue 1 (March 2020)

Volume 63 (2019): Issue 4 (December 2019)

Volume 63 (2019): Issue 3 (November 2019)

Volume 63 (2019): Issue 2 (June 2019)

Volume 63 (2019): Issue 1 (March 2019)

Volume 62 (2018): Issue 4 (December 2018)

Volume 62 (2018): Issue 3 (July 2018)

Volume 62 (2018): Issue 2 (May 2018)

Volume 62 (2018): Issue 1 (February 2018)

Volume 61 (2017): Issue 5 (December 2017)

Volume 61 (2017): Issue 4 (October 2017)

Volume 61 (2017): Issue 3 (July 2017)

Volume 61 (2017): Issue 2 (April 2017)

Volume 61 (2017): Issue 1 (March 2017)

Volume 60 (2016): Issue 5 (December 2016)

Volume 60 (2016): Issue 4 (December 2016)

Volume 60 (2016): Issue 3 (September 2016)

Volume 60 (2016): Issue 2 (June 2016)

Volume 60 (2016): Issue 1 (March 2016)

Volume 59 (2015): Issue 4 (December 2015)

Volume 59 (2015): Issue 3 (November 2015)

Volume 59 (2015): Issue 2 (July 2015)

Volume 59 (2015): Issue 1 (April 2015)

Volume 58 (2014): Issue 4 (December 2014)

Volume 58 (2014): Issue 3 (November 2014)

Volume 58 (2014): Issue 2 (June 2014)

Volume 58 (2014): Issue 1 (March 2014)

Volume 57 (2013): Issue 4 (December 2013)

Volume 57 (2013): Issue 3 (September 2013)

Volume 57 (2013): Issue 2 (June 2013)

Volume 57 (2013): Issue 1 (March 2013)

Volume 56 (2012): Issue 4 (December 2012)

Volume 56 (2012): Issue 3 (October 2012)

Volume 56 (2012): Issue 2 (July 2012)

Volume 56 (2012): Issue 1 (March 2012)

KOM – Corrosion and Material Protection Journal

The journal is primarily focused on corrosion engineering and surface treatment of metallic materials. We accept also articles concerning degradation of paints, enamels and other non-metallic materials used for corrosion prevention of metals. Another field of interest is conservation and restoration of cultural heritage. In this case we accept contributions concerning all materials (metals, wood, paper, leather, textiles, stone, glass and ceramics).  Why subscribe and read   Official Journal of the Association of Czech and Slovak Corrosion Engineers, premier source of high quality research results from all over the world with special emphasis on Central and Eastern Europe;  over 55 years of experience in publishing original papers dealing with corrosion science, engineering and technology;  focused on research in corrosion and surface treatment as well as experiences in practice and „case studies“;  original papers that advance understanding of both the fundamentals of corrosion and its application;  excellent articles authored by researchers from all over the world, who appreciate our fast, fair and constructive peer review provided by experts in the field of corrosion engineering.   Why submit   Fast, fair and constructive peer review  Fast publication process („submission→published article“ takes usually 3-6 months)  High quality electronic publication technologies  Open access (simple and charge-free access for every researcher)   Rejection Rate   10%   Archiving  Sciendo archives the contents of this journal in Portico - digital long-term preservation service of scholarly books, journals and collections.  Plagiarism Policy  The editorial board is participating in a growing community of Similarity Check System's users in order to ensure that the content published is original and trustworthy. Similarity Check is a medium that allows for comprehensive manuscripts screening, aimed to eliminate plagiarism and provide a high standard and quality peer-review process. 

KOM – Corrosion and Material Protection Journal

Volume 62 (2018): Issue 2 (May 2018)

EIS and corrosion behaviour of plasma sprayed layers of Al and AlCr6Fe2 on AZ91

Effect of combined surface treatment on quality and electrochemical corrosion properties of manganese phosphate on hsla steel domex 700

Influence of the adhesive type and metal substrate on adhesion of bonded joints after salt spray test

Influence of soil microorganisms on metal corrosion of underground pipelines

Failure of electric products by H₂S

Buscar

Todos los volúmenes y ediciones en esta revista