<abstract xmlns="http://www.w3.org/1999/xhtml">

Based on the commercial aluminium alloy powder blend (Alumix 431D) metal matrix composites reinforced with particles of SiC as well as TiC were produced by conventional powder metallurgy technology and the effect of the type and amounts of reinforced particles on the selected properties and microstructure of sintered composites were investigated. In particular, the densification behaviour, the wear resistance and the corrosion resistance in 3.5% NaCl solution were identified. It was stated that both the type and the weight fraction of carbide used as particulate reinforcement have a great impact on the properties of aluminium alloy matrix composites. It was shown that the introduction of titanium carbide has a more favourable effect on the properties of sintered Alumix 431D matrix composites in comparison to silicon carbide and the optimum content of TiC in composite is 4 wt. % due to the highest hardness, wear resistance (wear rate of 2.865·10−3 mm3/m) and simultaneously the best corrosion resistance (corrosion rate of 0.005 mm/year).
</abstract>

Based on the commercial aluminium alloy powder blend (Alumix 431D) metal matrix composites reinforced with particles of SiC as well as TiC were produced by conventional powder metallurgy technology and the effect of the type and amounts of reinforced particles on the selected properties and microstructure of sintered composites were investigated. In particular, the densification behaviour, the wear resistance and the corrosion resistance in 3.5% NaCl solution were identified. It was stated that both the type and the weight fraction of carbide used as particulate reinforcement have a great impact on the properties of aluminium alloy matrix composites. It was shown that the introduction of titanium carbide has a more favourable effect on the properties of sintered Alumix 431D matrix composites in comparison to silicon carbide and the optimum content of TiC in composite is 4 wt. % due to the highest hardness, wear resistance (wear rate of 2.865·10−3 mm3/m) and simultaneously the best corrosion resistance (corrosion rate of 0.005 mm/year).

The influence of carbide reinforcement on the properties of sintered aluminium alloy matrix composites

Department of Materials Engineering, Faculty of Materials Engineering and Physics

Technical Transactions

This work is licensed under the Creative Commons Attribution-ShareAlike 4.0 International License.

Based on the commercial aluminium alloy powder blend (Alumix 431D) metal matrix composites reinforced with particles of SiC as well as TiC were produced by...

The influence of carbide reinforcement on the properties of sintered aluminium alloy matrix composites

Publicado en línea: 16 abr 2023

Páginas: -

Recibido: 26 ene 2023

Aceptado: 11 abr 2023

DOI: https://doi.org/10.37705/TechTrans/e2023005

Palabras clave
aluminium alloy matrix composites, Alumix 431D, SiC, TiC, density, hardness, wear resistance, corrosion resistance, microstructure

© 2023 Aneta Szewczyk-Nykiel, published by Sciendo

This work is licensed under the Creative Commons Attribution-ShareAlike 4.0 International License.

The influence of carbide reinforcement on the properties of sintered aluminium alloy matrix composites

Publicado en línea: 16 abr 2023

Páginas: -

Recibido: 26 ene 2023

Aceptado: 11 abr 2023

DOI: https://doi.org/10.37705/TechTrans/e2023005

Palabras clavealuminium alloy matrix composites, Alumix 431D, SiC, TiC, density, hardness, wear resistance, corrosion resistance, microstructure

© 2023 Aneta Szewczyk-Nykiel, published by Sciendo

This work is licensed under the Creative Commons Attribution-ShareAlike 4.0 International License.

Palabras clave
aluminium alloy matrix composites, Alumix 431D, SiC, TiC, density, hardness, wear resistance, corrosion resistance, microstructure