Influence of Finish Milling Strategies on the Tool Wear

1. M. FONTAINE, A. DEVILLEZ, A. MOUFKI, D. DUDZINSKI. 2007. Modeling of cutting forces in ball end milling with tool surface inclination, Part II. Influence of cutting conditions, run-out, ploughing and inclination angle. J. Mater. Process. Technol., 189(1–3), pp. 85–89.10.1016/j.jmatprotec.2007.01.007Search in Google Scholar

2. A. DAYMI, M. BOUJELBENE, J.M. LINARES, E. BAYRAKTAR, A. BEN AMARA. 2009. Influence of workpiece inclination angle on the surface roughness in ball end milling of the titanium alloy Ti–6Al–4V. J. Achiev. Mater. Manuf. Eng., 35(1), pp. 79–86.Search in Google Scholar

3. C.E.H. VENTURA, A. HASSUI. 2013. Evaluation of static cutting forces and tool wear in HSM process applied to pocket milling. Int. J. Adv. Manuf. Tech. 65, pp. 1681-1689.10.1007/s00170-012-4290-1Search in Google Scholar

4. T. VOPÁT, J. PETERKA, V. ŠIMNA, M. KURUC. 2015. The influence of different types of copy milling on the surface roughness and tool life of end mills. Procedia Engineering, Vol. 100, pp. 868–876. ISSN 1877-705810.1016/j.proeng.2015.01.443Search in Google Scholar

5. D. BEGIC-HAJDAREVIC, M. KULENOVIC, A. CEKIC. 2014. Experimental study on the high speed machining of hardened steel. Procedia Engineering, Vol. 69, pp. 291–295.10.1016/j.proeng.2014.02.234Search in Google Scholar

6. T. XIANHUA, Z. JUN. 2013. Effect of cutting speed on cutting forces and wear mechanisms in high-speed face milling of Inconel 718 with Sialon ceramic tools. Int. J. Adv. Manuf. Tech. 69, pp. 2669-2678.10.1007/s00170-013-5206-4Search in Google Scholar

7. C. XIAOXIAO, Z. JUN, H. SHIGUO. 2013. Effects of inclination angles on geometrical features of machined surface in five-axis milling. Int. J. Adv. Manuf. Tech. 65, pp. 1721-1733,10.1007/s00170-012-4293-ySearch in Google Scholar

8. H. SCHULZ, S. HOCK. (1995). High-speed milling of die and moulds – cutting conditions and technology. Annals of the CIRP, 44, pp. 35-38.10.1016/S0007-8506(07)62270-7Search in Google Scholar

9. Z. SONG, L. JIAN-FENG. 2010. Tool wear criterion, tool life, and surface roughness during high speed steel end milling Ti-6Al-4V. J. Zhejiang Univ. Sci., A. 8, pp. 587-595.10.1631/jzus.A0900776Search in Google Scholar

10. K.A. KADIRGAMAA, A. ABOU-EL-HOSSEINB. 2011. Tool life and wear mechanism when machining Hastelloy C-22HS. Elsevier Wear, 270, pp. 258–268.10.1016/j.wear.2010.10.067Search in Google Scholar

11. Q. XINYI, L. PENGNAN. 2014. Study on serrated chip formation and tool wear of cermet tools for milling stainless steel 3Cr13Cu. Int. J. Adv. Manuf. Tech., 77, pp. 461-467.10.1007/s00170-014-6476-1Search in Google Scholar

12. M.B. DA SILVA, V.T.G. 2011. Naves, Analysis of wear of cemented carbide cutting tools during milling operation of gray iron and compacted graphite iron. Wear, 271, pp. 2426-2432.10.1016/j.wear.2010.11.030Search in Google Scholar

13. M. ZETEK. I. CESAKOVA, V. SVARC. 2014. Increasing Cutting Tool Life when Machining Inconel 718. Procedia Engineering, Vol. 69, pp. 1171–1179.10.1016/j.proeng.2014.03.099Search in Google Scholar

14. M.S. KASIMA. C.H. CHE HARONB, J.A. GHANIB et al. 2013. Wear mechanism and notch wear location prediction model in ball nose end milling of Inconel 718. Wear, 302(1–2).10.1016/j.wear.2012.12.040Search in Google Scholar

15. J. URMINSKÝ, R. ZAUJEC. 2018. Analysis of hardfacing and milling of forging die by CAx technologies. Materials Science Forum, Vol. 919, s. 354-361. ISSN 0255-547610.4028/www.scientific.net/MSF.919.354Search in Google Scholar

16. C.C. TAI, K.H. FHU. 1994. A predictive force model in ball-end milling including eccentricity effects. Int. J. Mach. Tools Manufact. 34, pp. 959–979.10.1016/0890-6955(94)90028-0Search in Google Scholar

17. J. PETERKA. 1997. Rozbor geometrie a kinematiky kopírovacieho frézovania. (Analysis of the geometry and kinematics of copy milling.) In: Vedecké práce MTF STU in Trnava, 5, pp. 53-58. ISBN 80-227-1005-9Search in Google Scholar