<abstract xmlns="http://www.w3.org/1999/xhtml">

The paper described the experimental findings of underwater wet welding of E40 steel using self-shielded flux-cored wire with a TiO2-FeO-MnO slag system. The arc stability, weld quality and corrosion resistance with different heat inputs were studied. The results showed that the wet welding process of the designed wire displayed good operability in the range of investigated parameters. The microstructure and mechanical properties of the weld metal depended on the heat input. Due to the high fraction of acicular ferrite in the weld metal, the mechanical properties of the weld metal under low heat input had better tensile strength and impact toughness. Fracture morphologies at low heat input had uniform and small dimples, which exhibited a ductile characteristic. The diffusible hydrogen content in the deposited metal obtained at a heat input of 26 kJ/cm significantly reduced to 14.6 ml/100g due to the combined effects of Fe2O3 addition and the slow solidification rate of molten metal. The microstructure also had a significant effect on the corrosion resistance of the weld metal. The weld metal with high proportions of acicular ferrite at low heat input exhibited the lowest corrosion rate, while the base metal possessed a reduced corrosion resistance. These results were helpful to promote the application of low alloy high strength steel in the marine fields.
</abstract>

The paper described the experimental findings of underwater wet welding of E40 steel using self-shielded flux-cored wire with a TiO2-FeO-MnO slag system. The arc stability, weld quality and corrosion resistance with different heat inputs were studied. The results showed that the wet welding process of the designed wire displayed good operability in the range of investigated parameters. The microstructure and mechanical properties of the weld metal depended on the heat input. Due to the high fraction of acicular ferrite in the weld metal, the mechanical properties of the weld metal under low heat input had better tensile strength and impact toughness. Fracture morphologies at low heat input had uniform and small dimples, which exhibited a ductile characteristic. The diffusible hydrogen content in the deposited metal obtained at a heat input of 26 kJ/cm significantly reduced to 14.6 ml/100g due to the combined effects of Fe2O3 addition and the slow solidification rate of molten metal. The microstructure also had a significant effect on the corrosion resistance of the weld metal. The weld metal with high proportions of acicular ferrite at low heat input exhibited the lowest corrosion rate, while the base metal possessed a reduced corrosion resistance. These results were helpful to promote the application of low alloy high strength steel in the marine fields.

Investigation of Process Stability and Weld Quality of Underwater Wet Flux-Cored Arc Welding of Low-Alloy High-Strength Steel with Oxy-Rutile Wire

State Key Laboratory of Advanced Welding and Joining

Peter the Great St. Petersburg Polytechnic University

Polish Maritime Research

This work is licensed under the Creative Commons Attribution 4.0 International License.

The paper described the experimental findings of underwater wet welding of E40 steel using self-shielded flux-cored wire with a TiO2-FeO-MnO slag system. The...

Investigation of Process Stability and Weld Quality of Underwater Wet Flux-Cored Arc Welding of Low-Alloy High-Strength Steel with Oxy-Rutile Wire

Publicado en línea: 22 oct 2021

Páginas: 100 - 109

DOI: https://doi.org/10.2478/pomr-2021-0037

Palabras clave
Arc stability, Weld quality, Low alloy high-strength steel, Underwater wet welding

© 2021 Hongliang Li et al., published by Sciendo

This work is licensed under the Creative Commons Attribution 4.0 International License.

Investigation of Process Stability and Weld Quality of Underwater Wet Flux-Cored Arc Welding of Low-Alloy High-Strength Steel with Oxy-Rutile Wire

Publicado en línea: 22 oct 2021

Páginas: 100 - 109

DOI: https://doi.org/10.2478/pomr-2021-0037

Palabras claveArc stability, Weld quality, Low alloy high-strength steel, Underwater wet welding

© 2021 Hongliang Li et al., published by Sciendo

This work is licensed under the Creative Commons Attribution 4.0 International License.

Palabras clave
Arc stability, Weld quality, Low alloy high-strength steel, Underwater wet welding