<abstract xmlns="http://www.w3.org/1999/xhtml"><p>This paper is dedicated to Tekrone composite material utilization in agricultural machinery. In terms of its technical properties, tekrone is very similar to steel 60 that is used for production of plough mouldboards and landsides. However, Tekrone shows more preferable characteristics, because its friction coefficient (<italic>k<sub>f</sub></italic>) is 2.6 times lower in contrast to steel 60. This fact indicates that the draft resistance can be decreased by replacing the plough mouldboards and landsides made of steel 60 with their counterparts made of Tekrone. This science hypothesis was confirmed by experimental investigation results. Analyses showed that utilization of plough with Tekrone mouldboards and landsides instead of steel ones significantly reduces their sticking to the wet soil. This results in a “soil moves over plough mouldboard surface” process instead of a “soil moves over soil” process. The plough draft resistance was decreased by 13.6% after replacement of the steel equipment with Tekrone one. Simultaneously, the performance of new tractor-plough aggregate was increased by 12.6%, the specific fuel consumption was reduced by 11.8%, and the preserving probability of the agrotechnological ploughing depth tolerance (±2 cm) was increased from 88% to 93%.</p></abstract>

This paper is dedicated to Tekrone composite material utilization in agricultural machinery. In terms of its technical properties, tekrone is very similar to steel 60 that is used for production of plough mouldboards and landsides. However, Tekrone shows more preferable characteristics, because its friction coefficient (kf) is 2.6 times lower in contrast to steel 60. This fact indicates that the draft resistance can be decreased by replacing the plough mouldboards and landsides made of steel 60 with their counterparts made of Tekrone. This science hypothesis was confirmed by experimental investigation results. Analyses showed that utilization of plough with Tekrone mouldboards and landsides instead of steel ones significantly reduces their sticking to the wet soil. This results in a “soil moves over plough mouldboard surface” process instead of a “soil moves over soil” process. The plough draft resistance was decreased by 13.6% after replacement of the steel equipment with Tekrone one. Simultaneously, the performance of new tractor-plough aggregate was increased by 12.6%, the specific fuel consumption was reduced by 11.8%, and the preserving probability of the agrotechnological ploughing depth tolerance (±2 cm) was increased from 88% to 93%.

Influence of the Plough with Tekrone Mouldboards and Landsides on Ploughing Parameters

Tavria State Agrotechnological University

National University of Life and Environmental Sciences of Ukraine

Slovak University of Agriculture in Nitra

Acta Technologica Agriculturae

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

This paper is dedicated to Tekrone composite material utilization in agricultural machinery. In terms of its technical properties, tekrone is very similar to...

Influence of the Plough with Tekrone Mouldboards and Landsides on Ploughing Parameters

Publicado en línea: 20 feb 2020

Páginas: 40 - 45

DOI: https://doi.org/10.2478/ata-2020-0007

Palabras clave
ploughing, friction coefficient, draft resistance, soil sticking

© 2020 Volodymyr Nadykto et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

Influence of the Plough with Tekrone Mouldboards and Landsides on Ploughing Parameters

Publicado en línea: 20 feb 2020

Páginas: 40 - 45

DOI: https://doi.org/10.2478/ata-2020-0007

Palabras claveploughing, friction coefficient, draft resistance, soil sticking

© 2020 Volodymyr Nadykto et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

Palabras clave
ploughing, friction coefficient, draft resistance, soil sticking