<abstract xmlns="http://www.w3.org/1999/xhtml">

<p>The inherent properties of aluminum alloys often result in defects like deformation and porosity in joints and welds created through conventional fusion welding. Our paper investigates the impact of varying rotational speeds in the friction stir welding of 4mm thick 6063-T6 aluminum alloy, focusing on microscopic grain refinement and mechanical property alterations in T-joints. Using mechanical stretching and numerical simulation methods, we observed that the initial weld joint is robust, with minimal flying edges and a distinct fish-scale pattern on the surface. Moreover, the grain sizes in the weld’s core area are notably smaller than those in the region affected by the upper axial shoulder. The mechanical properties of the joint experienced a first increase and then a decrease in mechanical properties when the friction stir welding rotational speed, was increased from 600r/min to 1500r/min. Moreover, in 1000r/min rotational speed, the material welded tensile strength and yield strength of the best tensile strength compared to the raw material to enhance the 21MPa, yield strength of 30MPa, elongation close to the raw material of 89.86%.</p>
</abstract>

The inherent properties of aluminum alloys often result in defects like deformation and porosity in joints and welds created through conventional fusion welding. Our paper investigates the impact of varying rotational speeds in the friction stir welding of 4mm thick 6063-T6 aluminum alloy, focusing on microscopic grain refinement and mechanical property alterations in T-joints. Using mechanical stretching and numerical simulation methods, we observed that the initial weld joint is robust, with minimal flying edges and a distinct fish-scale pattern on the surface. Moreover, the grain sizes in the weld’s core area are notably smaller than those in the region affected by the upper axial shoulder. The mechanical properties of the joint experienced a first increase and then a decrease in mechanical properties when the friction stir welding rotational speed, was increased from 600r/min to 1500r/min. Moreover, in 1000r/min rotational speed, the material welded tensile strength and yield strength of the best tensile strength compared to the raw material to enhance the 21MPa, yield strength of 30MPa, elongation close to the raw material of 89.86%.

Mechanism of grain refinement in FSW joints of 6063-T6 aluminum alloy under different rotational speeds

Applied Mathematics and Nonlinear Sciences

This work is licensed under the Creative Commons Attribution 4.0 International License.

The inherent properties of aluminum alloys often result in defects like deformation and porosity in joints and welds created through conventional fusion...

Mechanism of grain refinement in FSW joints of 6063-T6 aluminum alloy under different rotational speeds

Publicado en línea: 22 may 2024

Páginas: -

Recibido: 30 ene 2024

Aceptado: 11 abr 2024

DOI: https://doi.org/10.2478/amns-2024-1179

Palabras clave
Friction stir welding, 6063-T6 aluminum alloy, Numerical simulation, Grain refinement, Mechanical properties

© 2024 Xuejiao Sun et al., published by Sciendo

This work is licensed under the Creative Commons Attribution 4.0 International License.

Mechanism of grain refinement in FSW joints of 6063-T6 aluminum alloy under different rotational speeds

Publicado en línea: 22 may 2024

Páginas: -

Recibido: 30 ene 2024

Aceptado: 11 abr 2024

DOI: https://doi.org/10.2478/amns-2024-1179

Palabras claveFriction stir welding, 6063-T6 aluminum alloy, Numerical simulation, Grain refinement, Mechanical properties

© 2024 Xuejiao Sun et al., published by Sciendo

This work is licensed under the Creative Commons Attribution 4.0 International License.

Palabras clave
Friction stir welding, 6063-T6 aluminum alloy, Numerical simulation, Grain refinement, Mechanical properties