<abstract xmlns="http://www.w3.org/1999/xhtml"><p>The input of this paper lies in displaying possibilities how to determine the condition of a coordinate measuring machine (CMM) based on a large number of repeated measurements. The number of repeated measurements exceeds common requirements for determining positioning accuracy. The total offset in the accuracy of spatial positioning consists of partial inaccuracies of individual axes. 6 basic errors may be defined at each axis. In a triaxial set, that translates into 18 errors, to which an offset from the perpendicularity between the axial pairs must be added. Therefore, the combined number of errors in a single position is 21. These errors are systemic and stem from the machine’s geometry. In addition, there are accidental errors to account for as well. Accidental errors can be attributed to vibrations, mass inertness, passive resistance, and in part to fluctuations in temperature. A peculiar set of systemic errors are time-varying errors. The nature of those errors may be reversible, for instance if they result from influence of temperature or elastic deformation. They can be also irreversible, for example as a result of wear and tear or line clogging, due to loosened connection or permanent deformation of a part post collision. A demonstration of thermal equalizing of the machine’s parts may also be observed in case of failure to adhere to a sufficient time interval from the moment the air-conditioning is turned on. Repeated measurements done on a selected axis with linear interferometer can provide complex information on the CMM condition and also on the machine’s interaction with the given technical environment.</p></abstract>

The input of this paper lies in displaying possibilities how to determine the condition of a coordinate measuring machine (CMM) based on a large number of repeated measurements. The number of repeated measurements exceeds common requirements for determining positioning accuracy. The total offset in the accuracy of spatial positioning consists of partial inaccuracies of individual axes. 6 basic errors may be defined at each axis. In a triaxial set, that translates into 18 errors, to which an offset from the perpendicularity between the axial pairs must be added. Therefore, the combined number of errors in a single position is 21. These errors are systemic and stem from the machine’s geometry. In addition, there are accidental errors to account for as well. Accidental errors can be attributed to vibrations, mass inertness, passive resistance, and in part to fluctuations in temperature. A peculiar set of systemic errors are time-varying errors. The nature of those errors may be reversible, for instance if they result from influence of temperature or elastic deformation. They can be also irreversible, for example as a result of wear and tear or line clogging, due to loosened connection or permanent deformation of a part post collision. A demonstration of thermal equalizing of the machine’s parts may also be observed in case of failure to adhere to a sufficient time interval from the moment the air-conditioning is turned on. Repeated measurements done on a selected axis with linear interferometer can provide complex information on the CMM condition and also on the machine’s interaction with the given technical environment.

Information Contents of a Signal at Repeated Positioning Measurements of the Coordinate Measuring Machine (CMM) by Laser Interferometer

Technical University of Košice, Faculty of Mechanical Engineering, Department of Production Technique, Letná 9, 040 02 Košice

Technical University of Košice, Faculty of Mechanical Engineering, Department of Biomedical Engineering and Measurement, Letná 9, 040 02 Košice

Measurement Science Review

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

The input of this paper lies in displaying possibilities how to determine the condition of a coordinate measuring machine (CMM) based on a large number of...

Information Contents of a Signal at Repeated Positioning Measurements of the Coordinate Measuring Machine (CMM) by Laser Interferometer

Publicado en línea: 26 oct 2016

Páginas: 273 - 279

Recibido: 25 may 2016

Aceptado: 17 oct 2016

DOI: https://doi.org/10.1515/msr-2016-0034

Palabras clave
Laser interferometer, CMM, machine’s condition

© 2016 Tomáš Stejskal et al., published by De Gruyter Open

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Information Contents of a Signal at Repeated Positioning Measurements of the Coordinate Measuring Machine (CMM) by Laser Interferometer

Publicado en línea: 26 oct 2016

Páginas: 273 - 279

Recibido: 25 may 2016

Aceptado: 17 oct 2016

DOI: https://doi.org/10.1515/msr-2016-0034

Palabras claveLaser interferometer, CMM, machine’s condition

© 2016 Tomáš Stejskal et al., published by De Gruyter Open

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Palabras clave
Laser interferometer, CMM, machine’s condition