Volumen 26 (2018): Heft 2 (June 2018)

The article is a summary of information about evaluation of a risk degree for a brown coal spontaneous ignition which is realized on the base of a database analysis of information about the development of stative quantities and desorbated gases in the stored bodies of the brown coal. The data were gained from the long term complex measurements which were realized at chosen companies during the coal mining in the previous parts of the project. In the last part of the project, we examined results of temperature models from thermographs with results of gasses and coal samples from the mines. Then, the influence of atmospheric conditions (insolation, water downfall, changes of barometric pressure etc.), the influence of coal mass degradation, the influence of physical and chemical factors, and the influence of other defective factors on the process of the coal spontaneous ignition. The gasmetry was assess with gas in-situ samples and laboratory gas models of indicative gasses for the spontaneous ignition, which were taken from the method of the thermic oxidation with the aim of the correlation finding for an epicentre of temperature within the spontaneous ignition.

Modern manufacturing entities often operate in capital groups, and their role is sometimes limited to the function of cost centers. From the legal point of view, however, they are separate entities obliged to apply transfer pricing regulations. Meeting the requirements of the arm's length principle can be very difficult at this time, given the relationships and conflicts of interest in the capital group. Complexity increases in capital groups operating in different countries, due to differences in tax regulations. The main purpose of the paper is to demonstrate that the need to valuate the sale of finished goods to a manufacturing entity, which is a subject to a different tax jurisdiction, may lead to a problem of compliance with the arm's length principle. In addition, the paper proposes a methodology for comparability analysis that may be used by manufacturing entities to defend conditions of setting transfer pricing. The paper presents the different functional profiles of manufacturing entities and points out the difficulties that they may encounter when preparing the comparability analysis. It has also been noted that there are differences in transfer pricing regulations in different countries, for example by analyzing Polish and Czech regulations. The lack of uniform benchmarking legislation can cause inconsistencies in the selection of comparable data, resulting in differences in transfer pricing. The paper uses the method of legal regulation review and analysis of results of published studies concerning the scope of transfer pricing and comparability analysis. The paper also adopts a case study analysis.

Every company must ensure that the production process proceeds without interferences. Within this article, the author uses the term “interferences” in reference to unplanned stoppages caused by breakdowns. Unfortunately, usually due to machine operators’ mistakes, machines break, which causes stoppages thus generating additional costs for the company. This article shows a cause and effect analysis of a breakdown in a production process. The FMEA as well as quality management tools: the Ishikawa diagram and Pareto chart were used for the analysis. Correction measures were presented which allowed for a significant reduction in the number of stoppages caused by breakdowns.

The paper deals with increasing processes efficiency at a production line of cylinder heads of engines in a production company operating in the automotive industry. The goal is to achieve improvement and optimization of test processes on a production line. It analyzes options for improving capacity, availability and productivity of processes of an output test by using modern technology available on the market. We have focused on analysis of operation times before and after optimization of test processes at specific production sections. By analyzing measured results we have determined differences in time before and after improvement of the process. We have determined a coefficient of efficiency OEE and by comparing outputs we have confirmed real improvement of the process of the output test of cylinder heads.

The paper presents the results of researches of temperature variations during flat peripheral grinding. It is shown that the temperature variations of the workpiece can reach 25...30% of the average values, which can lead to some thermal defects. A nonlinear two-dimensional thermophysical grinding model is suggested. It takes into account local changes in the cutting conditions: the fluctuation of the cut layer and the cutting force, the thermal impact of the cutting grains, and the presence of surface cavities in the intermittent wheel. For the numerical solution of the problem, the method of finite differences is adapted. Researches of the method stability and convergence are made, taking into account the specific nature of the problem. A high accuracy of the approximation of the boundary conditions and the nonlinear heat equation is provided. An experimental verification of the proposed thermophysical model was carried out with the use of installation for simultaneous measurement of the grinding force and temperature. It is shown that the discrepancy between the theoretical and experimental values of the grinding temperature does not exceed 5%. The proposed thermophysical model makes it possible to predict with high accuracy the temperature variations during grinding by the wheel periphery.

Poland has a strong ambition to evolve rapidly into a knowledge-driven economy. Since 2004, it has been the largest beneficiary of European Union cohesion policy funds among all member states. Between 2007 and 2013, Poland was allocated approximately EUR 67 billion, whereas for 2014-2020 the EU budget earmarked EUR 82.5 billion for Polish cohesion policy. This means that in the coming years, Poland’s R&D intensity will grow. But the question remains: is 27 years of free market economy enough to enable a country’s economy to become knowledge-based ? This paper offers an analysis of Polish R&D expenditures and investments in terms of their sources (business, government or higher education sectors), types (European Union or state aid) and areas of support (infrastructure, education or innovation). It also characterises the Polish R&D market with its strengths and weaknesses. Then, it examines the process of technology transfer in Poland, comparing it to best practice. Finally, the paper lays out the barriers to effective commercialisation that need to be overcome, and attempts to answer the question raised in its title.

Paper addresses the different methods for protecting intellectual property in modern knowledge-based economies. The focus of the paper is a comparison between the procedures for applying for patents in Poland and the United States. The comparison has been made from the perspective of the cost of obtaining and maintaining a patent in Poland, the United States and some other countries. The comparison has also been made from the perspective of the procedures for applying for a patent in different countries based on the Patent Cooperation Treaty. The paper also includes a comparison of the time needed for processing the patent application. Low cost provisional twelve-month patent pending protection available in the United States is also being discussed. The paper also provides some guidance and recommendations for conducting a patent search in order to validate the originality of the invention.

The aim of the paper was to improve service processes carried out by Knorr-Bremse Systemy Kolejowe Polska sp. z o.o. Particularly, emphasise unnecessary movements and physical efforts of employees. The indirect goal was to find a solution in the simplest possible way using the Muda ideology. In order to improve the service process at the beginning was executed the process mapping for the devices to be repaired, ie. brake callipers, electro-hydraulic units and auxiliary release units. The processes were assessed and shown as Pareto-Lorenz analysis. In order to determine the most time consuming process. Based on the obtained results use of a column crane with articulated arm was proposed to facilitate the transfer of heavy components between areas. The final step was to assess the effectiveness of the proposed solution in terms of time saving. From the company perspective results of the analysis are important. The proposed solution not only reduces total service time but also contributes to crew’s work comfort.

Penn State Hazleton has recently developed and implemented a new Engineering program with a focus on energy efficiency and energy sustainability. To accelerate the implementation cycle of the program, it was necessary to very rapidly create and establish the components of an ecosystem needed for the Engineering program to prosper and grow. This paper describes the individual components of the ecosystem as well as the methods used to establish them. The paper also discusses the different initiatives to increase enrollment as well as placement rates for graduates. Continuous quality improvement procedure applied to maintain the quality of the program is also being discussed.

This article refers to the reliability of road rollers used in a selected roadworks company. Information on the method of road rollers service and how the service affects the reliability of these rollers is presented. Attention was paid to the process of the implemented maintenance plan with regard to the machine's operational time. The reliability of road rollers was analyzed by determining and interpreting readiness coefficients.