<abstract xmlns="http://www.w3.org/1999/xhtml">

<p>The 1.4306 austenite stainless steel has been prominently utilized as a material in the automotive and aerospace industry. Considerable interest has been garnered in the machinability of stainless steel owing to its high strength and poor thermal conductivity. The aim of this study is to ascertain the influential cutting parameters, specifically the cutting speed and feed rate, on cut-ting forces, cutting temperature, and chip evaluation. Thus, austenite stainless steel was subjected to free-cutting using a carbide recessing tool under dry conditions. The principle of measuring cutting temperature, a complex procedure due to varying thermal homogeneity, was elucidated. For the turning experiments in question, the standard Taguchi orthogonal array L9 (3<sup>2</sup>), featuring two factors and three levels, was employed. The experimental results were analyzed using MiniTab 17 software. The findings reveal a substantial effect of feed rate on cutting force, cutting temperature, and chip evaluation. The highest cutting force and cutting temperature were observed at a feed rate of 0.15 mm/rev. Conversely, the cutting force was minimized at a cutting speed of 100 m/min, indicating potential for increasing the cutting speed. The augmentation of feed rate led to chip compression and discoloration, attributed to elevated cutting force and a larger chip cross-section that efficiently dissipates heat from the cutting zone.</p>
</abstract>

The 1.4306 austenite stainless steel has been prominently utilized as a material in the automotive and aerospace industry. Considerable interest has been garnered in the machinability of stainless steel owing to its high strength and poor thermal conductivity. The aim of this study is to ascertain the influential cutting parameters, specifically the cutting speed and feed rate, on cut-ting forces, cutting temperature, and chip evaluation. Thus, austenite stainless steel was subjected to free-cutting using a carbide recessing tool under dry conditions. The principle of measuring cutting temperature, a complex procedure due to varying thermal homogeneity, was elucidated. For the turning experiments in question, the standard Taguchi orthogonal array L9 (32), featuring two factors and three levels, was employed. The experimental results were analyzed using MiniTab 17 software. The findings reveal a substantial effect of feed rate on cutting force, cutting temperature, and chip evaluation. The highest cutting force and cutting temperature were observed at a feed rate of 0.15 mm/rev. Conversely, the cutting force was minimized at a cutting speed of 100 m/min, indicating potential for increasing the cutting speed. The augmentation of feed rate led to chip compression and discoloration, attributed to elevated cutting force and a larger chip cross-section that efficiently dissipates heat from the cutting zone.

Investigation of the effects of machining parameters on cutting conditions during orthogonal turning of austenite stainless steel

GAMF Faculty of Engineering and Computer Science, Department of Innovative Vehicles and Materials

Faculty of Transportation Engineering and Vehicle Engineering, Department of Automotive Technologies

Budapest University of Technology and Economics

Production Engineering Archives

This work is licensed under the Creative Commons Attribution 4.0 International License.

The 1.4306 austenite stainless steel has been prominently utilized as a material in the automotive and aerospace industry. Considerable interest has been...

Investigation of the effects of machining parameters on cutting conditions during orthogonal turning of austenite stainless steel

Online veröffentlicht: 22. Feb. 2024

Seitenbereich: 86 - 93

Eingereicht: 18. Sept. 2023

Akzeptiert: 08. Jan. 2024

DOI: https://doi.org/10.30657/pea.2024.30.8

Schlüsselwörter
Taguchi orthogonal turning, cutting forces, cutting temperature, chip morphology, tool wear

© 2024 Gábor Kónya et al., published by Sciendo

This work is licensed under the Creative Commons Attribution 4.0 International License.

Investigation of the effects of machining parameters on cutting conditions during orthogonal turning of austenite stainless steel

Online veröffentlicht: 22. Feb. 2024

Seitenbereich: 86 - 93

Eingereicht: 18. Sept. 2023

Akzeptiert: 08. Jan. 2024

DOI: https://doi.org/10.30657/pea.2024.30.8

SchlüsselwörterTaguchi orthogonal turning, cutting forces, cutting temperature, chip morphology, tool wear

© 2024 Gábor Kónya et al., published by Sciendo

This work is licensed under the Creative Commons Attribution 4.0 International License.

Schlüsselwörter
Taguchi orthogonal turning, cutting forces, cutting temperature, chip morphology, tool wear