Counterfort drains are one of the oldest methods of improving slope stability by controlling the groundwater level on the one hand [1] and by applying an extra load on the side of retaining forces on the other hand [2]. Lowering the groundwater level by means of counterfort drains reduces the pore water pressure, thus increasing the effective soil shear strength along potential failure planes [3, 4, 5]. A system of counterfort drains in a slope significantly increases its stability at moderate construction costs [3, 5, 6].
Counterfort drains are made below the groundwater level and the failure plane by cutting a system of trenches 1.0–2.0 m wide perpendicularly to the slope. The trench walls are reinforced with non-woven geotextile and side filled with all-in aggregate to protect the slope soil against suffusion. The trench is filled densely with coarse broken stone (stone wall) to the width 0.3–0.6 m less than the trench. Concrete troughs are laid on the counterfort bottom. A drainage line is made at the slope foot, and the collected groundwater is removed to a reservoir or an absorbing device [6, 7, 8]. Counterfort drains are often deep trenches perpendicular to the slope, protected with non-woven geotextile and filled with aggregate. Drain pipes are laid on the bottom to remove the collected groundwater [3, 4, 5, 6, 9, 10].
One of the basic design problems is a suitable location and depth of counterforts [11]. Deep drains (including counterfort drains) are usually designed using analytical methods [4]. These methods [12, 13, 14] are based on a number of assumptions concerning homogeneity and isotropy of the soil, permeability, porosity and boundary conditions. The occurrence of such conditions in the field is unlikely [11]. For this reason, Fitch [3], based on practical experience, presented guidelines for the placement and depth of counterforts and the predicted lowering of the groundwater level in the slope.
The stabilisation of slopes and embankments with counterfort drains has been used successfully worldwide [9, 10, 15, 16, 17]. Field studies conducted on structures indicate a large potential of counterforts to lower and stabilise the groundwater level over time [18, 3, 4, 5, 6].
This paper evaluates the effectiveness of reinforcing a damaged retaining embankment of a landfill by making counterfort drains in its slope. The system of counterfort drains changed the soil properties significantly over a long-term use. The evaluation was based on many years of field and laboratory tests and stability analysis. The field tests concerned the observation of
The municipal landfill is situated within the administrative borders of Zakopane, Poland. It is located on a mountain slope, cut by an erosion valley connected with a local creek. The landfill is of a slope type, being a part of a steep hillside with inclination reaching 50% of exposure.
Figure 1 presents the landfill cross-section. In order to obtain a sufficient capacity of the landfill in a natural slope (II, III, IV), a hillside has been cut that comprised a few slopes and shelves. A retaining embankment (I) was built on the landfill front, forming the landfill trough. The outer retaining embankment side consists of two slopes and a shelf on which a technological road is located. The earth structure height varies from 8 to 12 m, with a general inclination of about 30–32° (1:1.5). The upper slope inclination reaches 38°. In such a designed landfill, the retaining embankment performs the retaining function to protect the final hillside shape, which is filled with municipal waste (V) and closed with the organic layer (VI).
Six months after the landfill opening (July 2004), after an intensive rainfall, a landslide in the retaining embankment occurred. The landslide included the top, outer embankment slope at the length of >40 m and was asequent (Fig. 2a). The total loss of retaining embankment stability could lead to a construction and environmental disaster as a result of which the landfill would have had to be closed.
All field works were performed manually due to the land configuration. The probing was performed using the weight sounding test (WST). A dozen probes were made in the area of the largest damage. The drilling was performed in the vicinity of the WST probing. A macroscopic soil evaluation was performed during the drilling, and samples were taken for laboratory tests. Manual drilling allowed testing of the layer up to 2.5 m deep.
The testing proved that the retaining embankment is made of indigenous soil obtained from the hillside terracing for the landfill. The soil is an uncontrolled mixture of sandy silty clay (sasiCl) and clay (Cl) mixed with rocky material (mudstone and sandstone). The surface layers were in the very soft and soft consistency, deeper turning into the firm consistency. This statement is true for the whole retaining embankment, e.g. the top, slopes and the shelf on which the road is located. The firm consistency was achieved only at depths corresponding to natural subsoil and then gradually turned into a stiff consistency.
The reasons for the retaining embankment damage are extensively described in the paper [19]. The basic reasons include:
– the firm consistency of soils of which the retaining embankment was formed;
– forming of the retaining embankment directly on the natural slope;
– the absence of compaction control during the earthworks;
– the absence of drainage on the entire landfill area and
– the absence of any drainage treatment for correct water removal and soil consolidation in the retaining embankment.
The final protection was not made for reasons of economy [8, 19]; only a temporary protection was made that comprised a system of counterfort drains at the entire retaining embankment length (Fig. 2b). The counterfort drains were made by cutting eight trenches (P1–P8) 1.0 m wide and 5.0–7.0 m deep perpendicular to the slope. The distance between the counterforts was 15.0 m. A drainage line was made below the counterforts to remove the groundwater to a nearby water course. The retaining embankment repair was completed in 2005.
Despite the recommendations, cyclical monitoring of the retaining embankment and all displacement was not introduced and piezometers were not installed. The absence of monitoring made it difficult to evaluate the protection effectiveness and control the structure behaviour. Therefore, the soil consistency and water content in the retaining embankment monitoring were provided by ourselves. The retaining embankment conditions were monitored between 2007 and 2017 by means of periodic WST probing. In addition, the samples were taken for laboratory tests from the surface layer (down to about 2.0 m below the ground). The field tests were performed in autumn during good weather.
The soil samples were not taken for strength and strain tests during the whole period of study for economic and technical reasons. Such tests require soil samples with intact structure and water content (NNS [20], quality class 1 [21]). No suitable equipment and financial resources were available for such sampling.
The WST probing was performed at six points in the area of the largest embankment damage in 2004, at a halfway distance between the counterforts P1/P2, P2/P3 and P3/P4. Three probes were made into the soil from the top of embankment WST-1, WST-3 and WST-5, and the other three were made at a half-height of the top embankment slope WST-2, WST-4 and WST-6. Additional WST probing was made between counterforts P4/P5, WST-7 and WST-8 since 2007 (Fig. 3).
The WST probing results are shown in Figs. 4, 5, 6, 7, by comparing the probing from the top of the retaining embankment with the probing at the half-height of the slope.
The following numerical weights were applied for the WST probing in cases where the probe penetrates statically only as a result of applied load
At the field test stage, the peak
Analysis of the probing results indicates an increased number of
The drilling with soil sampling was conducted in three points from the top of the embankment near the WST-1, WST-2 and WST-3 probing locations. During the laboratory tests in successive years, the following retaining embankment soil properties were determined: water content
Laboratory test results in successive years (mean values from three boreholes).
Properties | Depth [m] | Years | ||||||
---|---|---|---|---|---|---|---|---|
2004 | 2007 | 2009 | 2011 | 2013 | 2015 | 2017 | ||
Water content | 0.5 | 38.13 | 33.81 | 30.74 | 29.64 | 29.01 | 30.17 | 28.13 |
2.0 | 34.14 | 31.41 | 30.78 | 30.06 | 29.42 | 30.20 | 28.46 | |
Plastic limit, | 0.5 | 24.74 | 24.05 | 24.17 | 24.06 | 24.63 | 24.24 | 24.24 |
2.0 | 24.87 | 24.15 | 24.12 | 23.98 | 23.98 | 25.04 | 24.26 | |
Liquid limit, | 0.5 | 51.15 | 51.02 | 50.44 | 50.57 | 49.65 | 51.07 | 51.11 |
2.0 | 50.60 | 50.84 | 50.65 | 51.21 | 49.85 | 48.96 | 50.05 |
The results of the laboratory tests confirm the improvement of retaining embankment soil consistency. Stabilisation of the water content and liquidity index is visible as early as in 2011.
The effectiveness of the temporary retaining embankment protection was also proved using the landfill stability analysis, taking into account the change in soil properties over time.
The SLOPE/W software was used to perform the calculations. The software allows for a stability analysis with the limit equilibrium method. The
The retaining embankment soil parameters, depending on the varying liquidity index
Retaining embankment soil parameters by liquidity index IL used in the stability calculations.
Properties | Years | ||||||
---|---|---|---|---|---|---|---|
2004 | 2007 | 2009 | 2011 | 2013 | 2015 | 2017 | |
Liquidity index, | 0.36, C | 0.27, C | 0.25, C | 0.22, C | 0.21, C/B | 0.22, C/B | 0.16, C/B |
Unit weight, | 20.0 | 20.0 | 20.0 | 21.0 | 21.0 | 21.0 | 21.0 |
Cohesion, | 12.0 | 14.0 | 15.0 | 17.0 | 24.0 | 23.0 | 26.0 |
Angle of internal friction, ϕ | 12.0 | 13.5 | 14.0 | 14.5 | 16.5 | 16.3 | 17.5 |
C – non-consolidated soils, B – consolidated soils, C/B – the arithmetic mean values from B and C curves
It is generally believed that soil properties presented in standard [25] are underestimated and the design based on them (method B) is safe.
Table 3 presents the parameters of the other soil layers used in the stability calculations. For municipal waste (V) and organic layer (VI), the properties were taken from the literature [26]. However, for natural layers (II, III and IV), the soil properties were taken from the geological documentation prepared for the landfill construction [27].
Parameters of the geotechnical layers used in the stability calculations [26, 27].
Geotechnical layer | Volumetric weight, γ [kN/m3] | Cohesion, | Angle of internal friction, ϕ |
---|---|---|---|
II (sasiCl/Cl, | 20.8 | 45.0 | 9.9 |
III (Co and sasiCl/Cl, | 20.6 | 46.8 | 10.8 |
IV (Carpathian flysch) | 22.0 | 63.0 | 36.0 |
V (municipal waste) | 11.0 | 10.8 | 19.8 |
VI (organic soil) | 16.0 | 13.0 | 3.2 |
sasiCl – silty clay, Cl – clay, Co – cobble
The total values of the angle of internal friction ϕ
The effective parameters have greater values of the angle of internal friction and lower cohesion values than the total values. It is noted in particular for high-liquidity index soils,
The calculations for each time variant were performed for the situation when the landfill was full of waste and covered with the organic layer. The stability analysis results are given in Fig. 9.
The empty landfill stability analysis was performed for the situation in July 2004 (Fig. 10a). The factor of safety (FS = 0.920) confirms the stability loss of the retaining embankment.
Analysis of the values from the performed stability calculations indicates that in the case when the retaining embankment soil is firm consistency, the factors of safety (FS < 1.3) are unsatisfactory from the point of view of landfill stability. The corresponding failure planes run through the retaining embankment (Fig. 10b). From 2011 onwards, when the retaining embankment soil is of a stiff consistency (FS > 1.3), the results are satisfactory and the landslide processes are unlikely (Fig. 10c). The analysis of the last three cases (FS > 1.5) indicates that the results are very satisfactory, and the corresponding failure planes are located in the slope part with the municipal waste (Fig. 10d).
The construction of counterfort drains stabilised the water conditions in the retaining embankment and accelerated the soil consolidation process. From 2007 onwards, the field tests did not indicate any groundwater seepage or leakage and cracks or landslides. The construction of counterfort drains improved the consistency of the retaining embankment soil. In 2010, when the landfill was closed, a horizontal drain was made in the top landfill part that additionally improved the soil and water conditions in the retaining embankment.
From 2011 onwards, when the retaining embankment soil has been of a stiff consistency (FS = 1.331), the results are satisfactory and the landslide processes are unlikely. Further consolidation and soil consistency changes improved the factor of safety in successive years (FS = 1.566).
A massive and dense counterfort structure also contributed to the improved retaining embankment stability.