In the design of pile subjected to lateral load, the lateral displacement at working loads should be within the permissible limit [18,20,22]. In addition, the second main key element in the design of laterally; loaded piles is the determination of ultimate lateral resistance that can be exerted by soil against the pile [25], particularly the ultimate soil pressure which occurred in the middle of the pile.
The performance of piles when subjected to lateral loads is responsive to soil properties in the upper part of soil layer [6,7]. As the surface layers may be subject to disturbance, practically, traditional soil parameters should be adopted in the calculation of lateral pile displacement. In the case of piles under lateral loading, the failure criterion of short piles under lateral loads when compared to those of long piles varies and unlike the design procedure is suitable.Therefore, studying the effect of slenderness on the lateral single isolated pile response is important and still needs more assessment.
From Figure 1, t can be observed that the pile in case of short pile failure criteria and free head condition failed by full pile rotation around the point near to the pile base. Whilst in case of fixed head, the pile maybe fully moved and, at the same time, with small rotation near to the pile base. On the other hand, the long pile failure occurs near to the pile head by pile fracture and keeps the other embedded length without failure. In the case of fixed head long pile, the failure occurred at the fracture point as well as pile cap [6,7]. Real pile behaviour generally falls somewhere between the free- and fixed-head conditions because a small rotation of the pile head is expected, even when the pile is connected to a cap [17].
Many researches have also been performed to study the response of laterally loaded piles in different types of soil. A preliminary survey of the literatures available on this topic was given by [6,7,14], but little knowledge was received regarding the influence of the pile slenderness ratio on the lateral pile response, in addition to the influence of lateral load magnitudes, cross sectional shape of the pile and flexural rigidity of the pile.
It is generally accepted that the finite element method is the major technique used in numerical analysis of geotechnical problems, particularly piles and soil consolidation. As reported by [20], the first attempt to study the lateral behaviour of piles includes a two-dimensional (2D) finite element model in the horizontal plane. Anagnostopoulos and Georgiadis (1992) attempted to explain the lateral pile response through an experimental model supported by a 2D finite element analysis. Other investigations have attempted to study the lateral response of pile under pure lateral load using the finite element approach [9,11,16,23,24]. In addition, the influence the lateral pile response in 3D finite element approach when the pile carried both axial and lateral loads was studied by [12,13] and [1,2].
Therefore, in this study, the importance of conducting a fundamental study is discussed. A fundamental study of the lateral pile response under pure lateral load was conducted by varying a simulation parameter of the pile material (i.e. the geometric dimension of the pile such as slenderness ratio,
Finite element analyses were performed using the software PLAXIS 3D Foundation. In the finite element method, a continuum is divided into a number of (volume) elements. Each element consists of a number of nodes. Each node has a number of degrees of freedom that correspond to discrete values of the unknowns in the boundary value problem to be solved. The finite element mesh used in the simulation of single pile analysis (shown in Fig. 2) consists of 15-nodes wedge element (1,134), including (1,099) soil element and (35) pile elements. The lateral load is applied at the tip of the pile that is found on the ground surface in the x-direction and at y-direction when axial loads are applied. Plain and 3D view for the finite element mesh of single pile and surrounded the soil mass is given in Figure 2. The outer boundaries of soil body of cubic shape are extended to 10D on the sides and 5D at the bottom of pile base.
Analyses were performed with several trail meshes with increasing mesh refinement until the displacement changes to very minimal with more refinement. The aspect ratio of elements used in the mesh is small and closed to the pile body near to the pile top and base. All the nodes of the lateral boundaries (right and bottom) are restrained from moving in the normal direction to the respective surface.
The finite element simulation includes the following constitutive relationships for pile, surrounded soil and interface element. The finite element includes a linear elastic model to simulate structural part of the problem (e.g. pile), Mohr-Coulomb model to represent the surrounded soil and 16-node interface elements to represent an interface element. These constitutive models are illustrated as follows:
This section used to assess the accuracy of the finite element approach in analysing laterally loaded piles and to verify certain details of the finite element such as pile displacement. The comparative case includes full-scale lateral load tests reported by [10]. The results of laboratory and field tests are used to identify the soil profiles and soil properties that are well instrumented.
The case study deals with lateral load in which the deflection response of bored piles in cemented sand was examined by field test on a single pile under lateral load [10]. All piles were 0.3 m in diameter and had a length of 3 or 5m. The site of this load test was in Kuwait. The soil profile consists of a medium dense cemented silty sand layer to a depth of 3 m. This is underlain by a medium dense to very dense silty sand with cemented lumps to the bottom of the borehole. The same load sequence as pile tests was applied to the pile after completing the whole geotechnical model for lateral pile tests. The properties of soil in the both cases are listed in Table 1.
Geotechnical properties of the soil layers.Saturated soil weight (kN/m3) Young’s modulus (kPa) Poisson’s ratio Cohesion intercept (kPa) Friction angle Medium dense cemented silty sand layer 18 1.3×104 0.3 20 35 Medium dense to very dense silty sand with cemented lumps 19 1.3×104 0.3 1 45 Pile - 2.0×109 0.15 - -
The comparison between the finite element results and field test data is shown in Figure 3. The numerical simulation is reasonably accurate for the problem of laterally loaded piles and pile-soil interaction over a wide range of deformation for 3 and 5m long piles. The pile with a length of 5m is highly resistance to the lateral load from the second pile length value. Comparable data were obtained between the experimental results of the three piles and the present simulation model. The results obtained from the numerical simulation for a pile of 5 m is relatively closed with the results obtained from the field test. Whilst the result from the numerical simulation is not too closed in case of 3-m long pile, it may be due to nonhomogeneous soil around the pile in field.
The study includes the lateral pile response (i.e. lateral pile displacement and lateral soil pressure) under pure lateral load. Two types of soil were used (i.e. cohesionless and cohesive soils). Lateral load intensity
Soil parameters for analysis of pile group.Parameters Unit Cohesionless soil Cohesive soil Unit weight, kN/m3 20.0 18.0 Young’s modulus, MPa 1.3 × 104 1.0 × 104 Poisson’s ratio, - 0.3 0.35 Cohesion intercept, MPa 0.1 5.0 Angle of internal friction, - 30 25
The lateral pile deformation and lateral soil resistance because of the lateral load are always influenced by the lateral load intensity and soil type as well as a pile slenderness ratio (
In general, the lateral pile responded closely in cases of both cohesionless and cohesive soils when small amounts of loading were applied to all cases of slenderness ratio. As shown in the results, the pile under low and a large amount of loading (in the case of cohesionless soil) presented more resistance (low lateral displacement) than the pile embedded in the cohesion soil. This is possibly due to high soil stiffness.
Lateral soil pressure (
The influence of the pile slenderness ratio on the lateral pile tip displacement is assessed by fixed pile diameter and increase in the pile length (i.e.
The p-y curve predicted from finite element at two depths (z=0 and z=L/5D from ground surface) for both cohesionless and cohesive soils is shown in Figure 6. The initial values of the computed p-y curves are insensitive to the soil type and pile diameter. The result from this is closed to the assumption by Fan and Long (2005). From this figure, it can be observed that the behaviour of p–y curves was non-linear which results from the non-linear relationship of ultimate lateral soil pressure with respect to pile slenderness ratio; this also supported the assumption [25] and unsupported the assumption proposed [6,7], which observed linear relation of the ultimate lateral soil pressure with respect to pile slenderness ratio.
One of the main advantages of the 3D finite element simulation is the personification of the shape effect. The previous investigations show that the response of pile to lateral load is moderately affected by the shape of cross section [15]. Therefore, this study includes mainly the effect of pile shape on the lateral pile response on both cohesionless and cohesive soils.
The lateral pile displacement of two pile shapes is shown in Figure 7, which detailed the increase in lateral deflection response with an increased amount of loading. Pile deflection change depends on the pile load increment. In the first stage of load, the pile response was uniform, which means that the pile deflection improves linearly. But the square-shaped pile shows more resistance than a circular pile, because of the high contact surface area between the pile and surrounding soil.
The results (Fig. 7) show distribution of the soil resistance along the pile depth under 450 kN load for two types of soil. As concluded from this and the previous section, the soil resistance for different pile shapes does not significantly change at low load level. It can be observed that the cross section of square-shaped pile has high amount of lateral soil pressure than those observed from the circular pile. This happened possibly due to a large contact surface area of the square-shaped pile compared with the circular pile. This assumption is supported by [15].
The maximum tip deflections of two shapes of pile are detailed in Figure 8. In general, for the low values of load, the lateral pile response was closed for the cross section of two shapes of pile and always near to the linear behaviour. Whilst, at higher loads, the piles behaved non-uniformly resulting from the non-linear response of soil around the pile, and this is supported [9]. From these results, it was mainly observed that the square-shaped pile is able to resist the load by about 30% more than the circular pile.
The p–y curve predicted from finite element at two depth (z=0 and z=L/5D) for both cohesionless and cohesive soils is shown in Figure 9. The p–y curves were predicted for two shapes of the pile (i.e. square shaped and circular). From this figure, it can be observed that different behaviours of pile with different shapes translate into different design values, if necessary, to design pile under lateral load. Therefore, it can be concluded that the pile is more sensitive to the pile shape as well as pile slenderness ratio.
In this study, the flexural rigidity (
The distribution of lateral soil resistance with pile depth embedded on two types of soil is illustrated in Figures 10 and 11. For the same lateral load condition, the pile with low value of
The influence of the pile slenderness ratio
The study made comparison of both types of soil under three amounts of
The p–y curve predicted from finite element at two depths (z = 0 and z = L/5D) for both cohesionless and cohesive soils is shown in Figure 13. From this figure, it can seem that different behaviour of pile with different
The lateral pile deformation and lateral soil resistance because of the lateral load is always influenced by the lateral load intensity and soil type as well as a pile slenderness ratio (
The square-shaped pile has more resistance compared with a circular pile. The square-shaped pile is able to resist the load by about 30% more than the circular pile. The cross section of square-shaped pile has high amount of lateral soil pressure compared with those observed from the circular pile. Therefore, the p–y design curve is more sensitive to the pile shape as well as a pile slenderness ration. A pile in cohesionless soil was less affected by the change in