<abstract xml:lang="en" xmlns="http://www.w3.org/1999/xhtml"><p>In this study, the Taguchi method of design of experiment (DOE) was used to optimize the hydroxyapatite (HA) coatings on various metallic substrates deposited by sol-gel dip-coating technique. The experimental design consisted of five factors including substrate material (A), surface preparation of substrate (B), dipping/withdrawal speed (C), number of layers (D), and calcination temperature (E) with three levels of each factor. An orthogonal array of L18 type with mixed levels of the control factors was utilized. The image processing of the micrographs of the coatings was conducted to determine the percentage of coated area (PCA). Chemical and phase composition of HA coatings were studied by XRD, FT-IR, SEM, and EDS techniques. The analysis of variance (ANOVA) indicated that the PCA of HA coatings was significantly affected by the calcination temperature. The optimum conditions from signal-to-noise (S/N) ratio analysis were A: pure Ti, B: polishing and etching for 24 h, C: 50 cm min−1, D: 1, and E: 300 °C. In the confirmation experiment using the optimum conditions, the HA coating with high PCA of 98.5 % was obtained.</p></abstract>

In this study, the Taguchi method of design of experiment (DOE) was used to optimize the hydroxyapatite (HA) coatings on various metallic substrates deposited by sol-gel dip-coating technique. The experimental design consisted of five factors including substrate material (A), surface preparation of substrate (B), dipping/withdrawal speed (C), number of layers (D), and calcination temperature (E) with three levels of each factor. An orthogonal array of L18 type with mixed levels of the control factors was utilized. The image processing of the micrographs of the coatings was conducted to determine the percentage of coated area (PCA). Chemical and phase composition of HA coatings were studied by XRD, FT-IR, SEM, and EDS techniques. The analysis of variance (ANOVA) indicated that the PCA of HA coatings was significantly affected by the calcination temperature. The optimum conditions from signal-to-noise (S/N) ratio analysis were A: pure Ti, B: polishing and etching for 24 h, C: 50 cm min−1, D: 1, and E: 300 °C. In the confirmation experiment using the optimum conditions, the HA coating with high PCA of 98.5 % was obtained.

Optimization of sol-gel technique for coating of metallic substrates by hydroxyapatite using the Taguchi method

Nanotechnology and Advanced Materials Department, Materials and Energy Research Center, P.O. Box: 31787/316, Karaj, Iran

Department of Materials Engineering, Faculty of Mechanical Engineering, University of Tabriz, P.O. Box 51666-16471, Tabriz, Iran

Materials Science-Poland

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

In this study, the Taguchi method of design of experiment (DOE) was used to optimize the hydroxyapatite (HA) coatings on various metallic substrates deposited...

Optimization of sol-gel technique for coating of metallic substrates by hydroxyapatite using the Taguchi method

Online veröffentlicht: 29. Aug. 2013

Seitenbereich: 424 - 433

DOI: https://doi.org/10.2478/s13536-013-0119-3

Schlüsselwörter
hydroxyapatite, sol-gel, coating, Taguchi method, image processing

© 2013 Wroclaw University of Technology

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Optimization of sol-gel technique for coating of metallic substrates by hydroxyapatite using the Taguchi method

Online veröffentlicht: 29. Aug. 2013

Seitenbereich: 424 - 433

DOI: https://doi.org/10.2478/s13536-013-0119-3

Schlüsselwörterhydroxyapatite, sol-gel, coating, Taguchi method, image processing

© 2013 Wroclaw University of Technology

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Schlüsselwörter
hydroxyapatite, sol-gel, coating, Taguchi method, image processing