[
Abdelbary, A., Abouelwafa, M. & El Fahham, I.M. (2014) Evaluation and prediction of the effect of load frequency on the wear properties of pre-cracked nylon 66. Friction 2(3), 240-254. Al-Habahbeh, O.M. & Al-Huniti, N.S. (2005) Composite Pressure Vessels in Petroleum Industry. Status and Outlook, February.10.1007/s40544-014-0044-4
]Search in Google Scholar
[
Balya, B. (2004) Design and Analysis of Filament Wound Composite Tubes. December.
]Search in Google Scholar
[
Faramarzi, I. & Kashani, M. (2015) Improvements in tribological properties of polyamide 6 by application of aramid pulp. Iran Polym. J., 24, 329-335.
]Search in Google Scholar
[
Karpuz, P. & Alpay, A. (2005) Mechanical Characterization of Filament Wound Composite Tubes by Internal Pressure Testing, May.
]Search in Google Scholar
[
Kim, C.U., Kang, J.H., Hong, C.S. & Kim, C.G. (2005) Optimal design of filament wound structures under internal pressure based on the semi-geodesic path algorithm. Composite Structures, 67(4), 443-452.10.1016/j.compstruct.2004.02.003
]Search in Google Scholar
[
Mark, J.E. (ed.) (2007) Physical Properties of Polymers Handbook. 2nd Edition, Polymer Research Center and Department of Chemistry University of Cincinnati, Cincinnati, Ohio.
]Search in Google Scholar
[
Njuguna, J. (2016) Lightweight Composite Structures in Transport Design, Manufacturing, Analysis and Performance. Elsevier.
]Search in Google Scholar
[
Önder, A. (2007) First failure pressure of composite pressure vessels. Production of Composite Pressure Vessels, 100-115.
]Search in Google Scholar
[
Pihtili, H. (2009) An experimental investigation of wear of glass fibre-epoxy resin and glass fibre-polyester resin composite materials. European Polymer Journal, 45(1), 149-154.10.1016/j.eurpolymj.2008.10.006
]Search in Google Scholar
[
Reshma, A.J. (2017) Review on burst pressure analysis of laminated composite pressure vessels. International Research Journal of Engineering and Technology, 4(5), 2738-2742.
]Search in Google Scholar
[
Rubin, I. (1990) Handbook of plastic materials and technology. Wiley, New York.
]Search in Google Scholar
[
Saad, N., Al-Zubiedy, A. & Mahmood M. (2017) Improvement mechanism of fracture toughness of HDPE with mixing mechanism (Nano particle) for pipe application. International Journal of Applied Engineering Research (IJAER), 12, 24.
]Search in Google Scholar
[
Sikora, R., Flizikowski, J. & Al-Zubiedy, M.A. (1993) Effect of injection moulding parameters of toothed wheels and type of polyamide material on the kinematic gear ratio of a belt transmission with these wheels. International Polymer Science and Technology, 20, 4.
]Search in Google Scholar
[
Tiwari, N. (2015) Manufacturing of Thermoset Composites, 11.
]Search in Google Scholar
[
Vishwanath, B., Verma, A. & Kameswara Rao, C. (1992) Effect of matrix content on strength and wear of woven roving glass polymeric composites. Composite Science and Technology, 44(1), 77-86. Yousefpour, R. (2002) Epoxy Woven Composite Material for a Semi-Autonomous (Vol. 36).10.1016/0266-3538(92)90027-Z
]Search in Google Scholar
, 