<abstract xmlns="http://www.w3.org/1999/xhtml"><p>The purpose of this research is unsatisfactory state of knowledge of the abrasive wear of composites with thermoplastic polymer as matrix material and reinforcing material in the form of short and focused carbon fibers that can be used in additive manufacturing technologies. The paper presents a conceptual design of an extrusion head used in Fused Deposition Technology, which allows for the implementation of appropriately stacked fibers at the level of detail production. Finite element simulation was performed to simulate the thermal effect of the system to demonstrate the effect of head cooling on the system. The assumed extrusion temperature of the material was obtained at a uniform nozzle temperature and stable temperature of the entire system. Flow simulation of thermoplastic polymer was carried out in the designed extrusion nozzle. By supplying 0.5 mm wire of 1.75 mm diameter thermoplastic material to the nozzle, the extrusion rate was 0.192 m/s. The proper design of the extrusion head for the intended applications has been demonstrated and the purpose of further research in this field has been confirmed.</p></abstract>

The purpose of this research is unsatisfactory state of knowledge of the abrasive wear of composites with thermoplastic polymer as matrix material and reinforcing material in the form of short and focused carbon fibers that can be used in additive manufacturing technologies. The paper presents a conceptual design of an extrusion head used in Fused Deposition Technology, which allows for the implementation of appropriately stacked fibers at the level of detail production. Finite element simulation was performed to simulate the thermal effect of the system to demonstrate the effect of head cooling on the system. The assumed extrusion temperature of the material was obtained at a uniform nozzle temperature and stable temperature of the entire system. Flow simulation of thermoplastic polymer was carried out in the designed extrusion nozzle. By supplying 0.5 mm wire of 1.75 mm diameter thermoplastic material to the nozzle, the extrusion rate was 0.192 m/s. The proper design of the extrusion head for the intended applications has been demonstrated and the purpose of further research in this field has been confirmed.

Simulation of Processes Occurring in the Extrusion Head Used in Additive Manufacturing Technology

Acta Mechanica et Automatica

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

The purpose of this research is unsatisfactory state of knowledge of the abrasive wear of composites with thermoplastic polymer as matrix material and...

Simulation of Processes Occurring in the Extrusion Head Used in Additive Manufacturing Technology

Online veröffentlicht: 30. Dez. 2017

Seitenbereich: 317 - 321

Eingereicht: 06. Juni 2017

Akzeptiert: 11. Dez. 2017

DOI: https://doi.org/10.1515/ama-2017-0049

Schlüsselwörter
Additive Manufacturing, Fused Deposition Modelling, FEM Analysis, RFPC

© 2017 Artur Prusinowski et al., published by De Gruyter Open

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

Simulation of Processes Occurring in the Extrusion Head Used in Additive Manufacturing Technology

Online veröffentlicht: 30. Dez. 2017

Seitenbereich: 317 - 321

Eingereicht: 06. Juni 2017

Akzeptiert: 11. Dez. 2017

DOI: https://doi.org/10.1515/ama-2017-0049

SchlüsselwörterAdditive Manufacturing, Fused Deposition Modelling, FEM Analysis, RFPC

© 2017 Artur Prusinowski et al., published by De Gruyter Open

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

Schlüsselwörter
Additive Manufacturing, Fused Deposition Modelling, FEM Analysis, RFPC