<abstract><title style='display:none'>Abstract</title> The flying-capacitor (FC) topology is one of the more well-established ideas of multilevel conversion, typically applied as an inverter. One of the biggest advantages of the FC converter is the ability to naturally balance capacitor voltage. When natural balancing occurs neither measurements, nor additional control is needed to maintain required capacitors voltage sharing. However, in order to achieve natural voltage balancing suitable conditions must be achieved such as the topology, number of levels, modulation strategy as well as impedance of the output circuitry. Nevertheless this method is effectively applied in various classes of the converter such as inverters, multicell DC-DC, switch-mode DC-DC, AC-AC, as well as rectifiers. The next important issue related to the natural balancing process is its dynamics. Furthermore, in order to reinforce the balancing mechanism an auxiliary resonant balancing circuit is utilized in the converter which can also be critical in the AC-AC converters or switch mode DC-DC converters. This paper also presents an issue of choosing modulation strategy for the FC converter due to the fact that the natural balancing process is well-established for phase shifted PWM whilst other types of modulation can be more favorable for the power quality.</abstract>

NATURAL CAPACITOR VOLTAGE BALANCE IN MULTILEVEL FLYING CAPACITOR CONVERTRS. A REVIEW OF RESEARCH ACHIEVEMENTS

<abstract><title style='display:none'>Abstract</title>Electromagnetic compatibility requirements for immunity tests have been presented and the emission levels of electromagnetic disturbances in adjustable speed power drive systems have been determined. The disturbances are divided into two groups: low-frequency (up to 50 harmonics of the power supply system) and high-frequency (above 150 kHz). The lack of legal regulations on permissible disturbance level in the frequency range from 2.5 kHz to 150 kHz has also been mentioned. This range is considered high frequency by the authors. Standarized compatibility levels and sample measured parameters of the electromagnetic environment have also been shown. An exemplary reaction of the drive to the most common disturbances in the power supply system has been presented.</abstract>

EMC Requirements for Power Drive Systems

<abstract><title style='display:none'>Abstract</title>The article presents the current state and development trends of electrical drives, with particular emphasis on modern control structures and safety systems of various types of electrical machines. Special attention was paid to the needs of industrial drive systems and a possibility of practical implementation of complex control algorithms. Development perspectives of electrical drives are discussed from the perspective of new trends in control, power electronics and electrical machines, with consideration given to systems robust to faults of drive system elements.</abstract>

Industrial Drive Systems. Current State and Development Trends

<abstract><title style='display:none'>Abstract</title>To improve the reliability of motor system, this paper investigates the sensor fault diagnosis methods for T-type inverter-fed dual three-phase permanent magnet synchronous motor (PMSM) drives. Generally, a T-type three-level inverter-fed dual three-phase motor drive utilizes four phase-current sensors, two direct current (DC)-link voltage sensors and one speed sensor. A series of diagnostic methods have been comprehensively proposed for the three types of sensor faults. Both the sudden error change and gradual error change of sensor faults are considered. Firstly, the diagnosis of speed sensor fault was achieved by monitoring the error between the rotating speed of stator flux and the value from speed sensor. Secondly, the large high-frequency voltage ripple of voltage difference between the estimated voltage and the reference voltage was used to identify the voltage sensor faults, and the faulty voltage sensor was determined according to the deviation of voltage difference. Thirdly, the abnormal current amplitude on harmonic subspace was adopted to identify the current sensor faults, and the faulty current sensor was located by distinguishing the current trajectory on harmonic subspace. The experiments have been taken on a laboratory prototype to verify the effectiveness of the proposed fault diagnosis schemes.</abstract>

Fault Diagnosis of Sensors for T-type Three-Level Inverter-fed Dual Three-Phase Permanent Magnet Synchronous Motor Drives

<abstract><title style='display:none'>Abstract</title>The paper presents a high-speed induction motor drive as an alternative for household appliances. A short comparison was made between standard and high-speed motors. The solutions that use three-phase induction motors were taken into consideration with different types of rotors: solid or squirrel-cage. The assumed power of drive was up to 1 kW. As the power source, a single-phase voltage source has been adopted, which was indirectly converted to a three-phase output voltages with the fundamental frequency up to 667 Hz.</abstract>

Review of Solutions Used in High-Speed Induction Motor Drives Operating in Household Appliances

<abstract><title style='display:none'>Abstract</title>The paper presents a linear-quadratic current controller with damped oscillatory terms designed for three-phase grid-tie voltage source converters used in SMES systems and operated under distorted grid voltage conditions. Special emphasis is placed on a synthesis of an anti-windup mechanism to prevent wind-up derived from the oscillatory terms by the use of a new active damping loop based on a simple moving average method. As a consequence, the current feedback gain may be increased without unwanted overshoot and overruns, and performance of the system can be improved.</abstract>

ANTI-WINDUP STRATEGY FOR AN LQ CURRENT CONTROLLER WITH OSCILLATORY TERMS FOR THREE-PHASE GRID-TIE VSCs IN SMES SYSTEMS

<abstract>
<title style='display:none'>Abstract</title>
Cell balancing, a critical aspect of battery management in electric vehicles (EVs) and other applications, ensures a uniform state of charge (SOC) distribution among individual cells within a battery pack, enhancing performance and longevity while mitigating safety risks. This paper examines the effectiveness of capacitor-based active cell-balancing techniques using simulations under dynamic loading conditions. Utilising MATLAB and Simulink, various circuit topologies are evaluated, considering real-world cell parameters and open-circuit voltage (OCV) curve modelling. Results indicate that advanced configurations, such as double-tiered switched-capacitor balancing, offer improved balancing speed and efficiency compared to conventional methods. However, challenges such as transient events during charging and discharging phases underscore the need for further research. By leveraging simulations and experimental data, researchers can refine cell-balancing strategies, contributing to the development of safer, more efficient battery systems for EVs and beyond. This study underscores the importance of systematic analysis and optimisation in advancing cell-balancing technology for future energy-storage applications.
</abstract>

Capacitor-Based Active Cell Balancing for Electric Vehicle Battery Systems: Insights from Simulations

<abstract>
<title style='display:none'>Abstract</title>
Generally in under-graduate studies, magnetizing inrush current (MIC) is discussed theoretically without giving much practical exposure. This paper presents the development of a low cost experimental set-up using a digital controller to study the MIC and the different parameters which can affect the same. This also helps to show how the inrush current can be minimized. This set-up also provides a hands-on experience of MIC and its control in under-graduate study, which can help an upcoming practitioner in industry as well as in further research. This paper presents a brief description of MIC, followed by a short analysis. Here, a pair of anti-parallel thyristors are connected in series with the primary winding of a single-phase power transformer. The turningon instant of this switch, with respect to the zero-crossing instant of the input supply voltage, may be adjusted through a firmware, in a PIC18F4620 from Microchip Technology microcontroller development board from Microchip Technology to control the transformer energisation instant. The firmware is developed in MPLABX-IDE from Microchip Technology, and the scheme is verified via simulations in Proteus simulation software. A suitable circuit to support the microcontroller development board to achieve the above function is designed and fabricated.
</abstract>

An Experimental Set-up Involving Low-cost Digital Controller to Study the Magnetizing Inrush Current in a Transformer using Point-on-Wave Switching Technique

<abstract>
<title style='display:none'>Abstract</title>
A quasi-Z-source network is used to boost the DC bus voltage of a voltage source two-level H-bridge inverter to increase the voltage gain. With the increase in the DC bus voltage, the common mode voltage (CMV) also increases. The CMV is reduced using virtual space vector pulse width modulation (SVPWM). Due to the presence of a quasi-Z-source network, the expression of the CMV changes significantly with respect to the conventional voltage source two-level H-bridge inverter fed from a pure DC supply. In this paper, a detailed analysis of the origin of the CMV for the quasi-Z-source two-level H-bridge inverter is presented. Additionally, it is shown how the CMV is affected for a DC input supply taken from a three-phase diode bridge rectifier. The work also details the scheme for suitable placement of shoot-through time intervals required for boosting within the non-active time intervals in virtual SVPWM. The simulation and experimental results show the scheme is effective in increasing the voltage gain and reducing the CMV arising at the third harmonic of the desired output frequency by at least 33.33%.
</abstract>

Quasi-Z-Source Three-Phase Voltage Source Inverter with Virtual Space Vector Modulation to Increase the Voltage Gain and for the Reduction of Common Mode Voltage

<abstract>
<title style='display:none'>Abstract</title>
The popularity of electrified transportation is rising at a sharp pace due to environmental concerns over internal combustion (IC) engines. Researchers are nowadays looking for a brushless and permanent magnet (PM)-less solution for electric vehicle (EV) motors. Wound-field synchronous motor (WFSM) is a potential solution for EVs and is being used in Renault Zoe EV and BMW iX3 e-Drive models. A Brushless Induction excited Synchronous Motor (BINSYM) is a WFSM where the exciter, an induction machine (IM), is embedded inside the synchronous machine (SM) frame. Two machines (SM and IM) are configured for different numbers of poles to achieve magnetic decoupling, which facilitates independent control of both machines. The purpose of IM is to maintain the excitation requirement of SM. The IM is controlled in deep-plugging mode at a constant slip frequency over the entire speed range to minimise its reactive power demand. The maximum torque per ampere (MTPA) and root mean square (rms) current minimisation algorithms are used to control the SM. Simulation of the BINSYM-based system under dynamic conditions (MTPA with varying field current and load transient) has been carried out in MATLAB/Simulink to validate the control strategies. Experimental findings from the laboratory prototype machine closely match the simulation results.
</abstract>

Excitation Control of Brushless Induction Excited Synchronous Motor with Induction Machine Operating in Deep-Plugging Mode

<abstract>
<title style='display:none'>Abstract</title>
This paper presents an experimental implementation of a Neural Sliding Mode Linearization approach for the control of a double-fed induction generator connected to an infinite bus via transmission lines. The rotor windings are connected to the grid via a back-to-back converter, while the stator windings are directly coupled to the network. The chosen control scheme is applied to obtain the required stator power trajectories by controlling the rotor currents and to track the desired values of the DC-link output voltage and the grid power factor. This controller is based on a neural identifier trained online using an Extended Kalman Filter. Based on such identifier, an adequate model is obtained, which is used for synthesizing the required controllers. The proposed control scheme is experimentally verified on 1/4 HP DFIG prototype considering normal and abnormal grid conditions. In addition, maximum power extraction from a random wind profile is tested in the presence of different grid scenarios. Moreover, a comparison with conventional control schemes is performed. The obtained results illustrate the capability of the proposed control scheme to achieve active power, reactive power, and DC voltage desired trajectories tracking and to operate the wind power system even in the presence of parameter variation and grid disturbances, which helps to ensure the stability of the system and improve generated power quality.
</abstract>

Real-time Neural Sliding Mode Linearization Control for a Doubly Fed Induction Generator under Disturbances

<abstract>
<title style='display:none'>Abstract</title>
The DTSTACOM is a power quality compensator that can be used in the distribution grid to compensate the demand of reactive power, which can be produced by different linear and non-linear loads. In this process, the control method of DSTATCOM is one of the key factors influencing the performance of DSTATCOM. This study aims to analyse the effect of two modulation schemes, Pulse Width Modulation (PWM) and Hysteresis Current Control (HCC), under several conditions. The proposed modelling approach and Synchronous Reference Frame (SRF) theory are used to verify reactive power compensation and total harmonic distortion (THD). Further, PWM and Hysteresis Current Control (HCC) with proportional-integral (PI) controller simulated in MATLAB for different cases, and percentage THD was calculated to prove the effectiveness of the proposed method for the control of reactive power and THD with grid-connected DSTATCOM. The results presented here justify that the HCC controller can be better than the PWM method to generate the PWM pulses for reduction of harmonics under various conditions of DTSTACOM to compensate the reactive power. Additionally, the simulation was performed to check the efficacy of the projected method to reduce THD by varying the current control band of HCC.
</abstract>

A Simulation Analysis of Grid-Connected DSTATCOM with PWM Voltage Control and Hysteresis Current Control for Power Quality Improvement

<abstract><title style='display:none'>Abstract</title>Smart grid (SG) is the solution to solve existing problems of energy security from generation to utilization. Examples of such problems are disruptions in the electric grid and disturbances in the transmission. SG is a premium source of Big Data. The data should be processed to reveal hidden patterns and secret correlations to extrapolate the needed values. Such useful information obtained by the so-called data analytics is an essential element for energy management and control decision towards improving energy security, efficiency, and decreasing costs of energy use. For that reason, different techniques have been developed to process Big Data. This paper presents an overview of these techniques and discusses their advantages and challenges. The contribution of this paper is building a recommender system using different techniques to overcome the most obstacles encountering the Big Data processes in SG. The proposed system achieves the goals of the future SG by (i) analyzing data and executing values as accurately as possible, (ii) helping in decision-making to improve the efficiency of the grid, (iii) reducing cost and time, (iv) managing operating parameters, (v) allowing predicting and preventing equipment failures, and (vi) increasing customer satisfaction. Big Data process enables benefits that were never achieved for the SG application.</abstract>

A Review on Big Data Management and Decision-Making in Smart Grid

<abstract><title style='display:none'>Abstract</title>This paper presents an estimator-based speed sensorless field-oriented control (FOC) method for induction machines, where the state estimator is based on a self-contained, non-linear model. This model characterises both the electrical and the mechanical behaviours of the machine and describes them with seven state variables. The state variables are estimated from the measured stator currents and from the known stator voltages by using an estimator algorithm. An important aspect is that one of the state variables is the load torque and, hence, it is also estimated by the estimator. Using this feature, the applied estimator-based speed sensorless control algorithm may be operated adequately besides varying load torque. In this work, two different variants of the control algorithm are developed based on the extended and the unscented Kalman filters (EKF, UKF) as state estimators. The dynamic performance of these variants is tested and compared using experiments and simulations. Results show that the variants have comparable performance in general, but the UKF-based control provides better performance if a stochastically varying load disturbance is present.</abstract>

Dynamic Performance of Estimator-based Speed Sensorless Control of Induction Machines Using Extended and Unscented Kalman Filters

<abstract><title style='display:none'>Abstract</title>A sensorless indirect stator-flux-oriented control (ISFOC) induction motor drive at very low frequencies is presented herein. The model reference adaptive system (MRAS) scheme is used to estimate the speed and the rotor resistance simultaneously. However, the error between the reference and the adjustable models, which are developed in the stationary stator reference frame, is used to drive a suitable adaptation mechanism that generates the estimates of speed and the rotor resistance from the stator voltage and the machine current measurements. The stator flux components in the stationary reference frame are estimated through a pure integration of the back electro-motive force (EMF) of the machine. When the machine is operated at low speed, the pure integration of the back EMF introduces an error in flux estimation which affects the performance torque and speed control. To overcome this problem, pure integration is replaced with a programmable cascaded low-pass filter (PCLPF). The stability analysis method of the MRAS estimator is verified in order to show the robustness of the rotor resistance variations. Experimental results are presented to prove the effectiveness and validity of the proposed scheme of sensorless ISFOC induction motor drive.</abstract>

A Very-Low-Speed Sensorless Control Induction Motor Drive with Online Rotor Resistance Tuning by Using MRAS Scheme

<abstract>
<title style='display:none'>Abstract</title>
This paper studies innovative application of sliding mode control (SMC) for a Hybrid Renewable Energy System (HRES) in grid-connected and autonomous modes of operation. The considered HRES includes a photovoltaic (PV), wind turbine (WT) based on a Permanent Magnet Synchronous Generator (PMSG). The PV generator is coupled to the common DC bus via a DC/DC converter. The latter is controlled by an MPPT algorithm based on the Adaptive Perturbation and Observation Algorithm Method (APOAM) to search the optimum working of this source. A SMC is utilized to manage the PV voltage to achieve the Maximum Power Point (MPP) by altering the obligation duty cycle. The battery interfaced by a bidirectional buck-boost DC/DC converter can be charged or discharged depending on the production situation. On the one hand, the wind turbine conversion chain is equipped with a PMSG and a rectifier controlled to regulate the operating point of the wind turbine to its optimum value. During a Stand-Alone Mode (SAM) operation, the Voltage Source Converter (VSC) was used for controlling the output voltage in terms of amplitude and frequency delivered to the AC load. However, in Grid-Connected Mode (GCM) operation, the VSC was adapted to control the electrical parameters of the grid. To better appreciate the advantages of the proposed SMC approach, we have proposed a series of comparative tests with the conventional PI control in the operating modes GC and SA and under different scenarios. The proposed control strategy has undeniable advantages in terms of control performance and very low total harmonic distortion THD value compared with the conventional PI control. Finally, It is concluded that the proposed approach improves the quality and provides a stable operation of the HRES.
</abstract>

Sliding Mode Control of Hybrid Renewable Energy System Operating in Grid Connected and Stand-Alone Mode

<abstract><title style='display:none'>Abstract</title>This paper presents the direct field-oriented control (DFOC) method of six-phase induction motor with the application of super-twisting sliding mode algorithm. The mathematical model of the six-phase induction motor has been described. The descriptions of the space vector modulation (SVM) method and the super-twisting algorithm have been presented. The DFOC method with super-twisting sliding mode controllers has been described. The experimental studies of the DFOC method with super-twisting controllers have been performed, and the results of these studies are presented and discussed.</abstract>

Application of Super-Twisting Sliding Mode Controllers in Direct Field-Oriented Control System of Six-Phase Induction Motor: Experimental Studies

<abstract>
<title style='display:none'>Abstract</title>
In this article, model reference adaptive system (MRAS)-based estimator of a rotor resistance of an induction motor (IM) is presented. In contrast to the solutions known from the literature, the reference model of this estimator uses the measured values of the phase current and the adaptive part is a virtual current sensor. The article presents an accurate description of the algorithm taking into account the discrete equations for possible practical implementation in the microprocessor system. In the first step, the impact of motor parameters to stator current estimation quality in the adaptive model was checked. Subsequently, simulation tests of the proposed rotor resistance estimator were carried out for the field-oriented control of the induction motor drive system with a model of an induction motor with fixed parameters and an induction motor with a changing main inductance according to a magnetisation curve. The analysis of the estimator’s work showed its high efficiency and insensitivity to changes in the IM main inductance.
</abstract>

Power Electronics and Drives