<abstract xml:lang="en"><title style='display:none'>Monte Carlo Calculations of Selected Dose Components in a Head Model for Boron Neutron Capture Therapy</title>Boron Neutron Capture Therapy is a very promising form of cancer therapy, consisting in irradiating a stable isotope of boron (10B) concentrated in tumor cells with a low energy neutron beam. This technique makes it possible to destroy tumor cells, leaving healthy tissues practically unaffected. In order to carry out the therapy in the proper way, the proper range of the neutron beam energy has to be chosen.In this paper we present the results of the calculations, using the MCNP code, aiming at studying the energetic dependence of the absorbed dose from the neutron capture reaction on boron (the therapeutic dose), and hydrogen and nitrogen (the injuring dose).</abstract>

Monte Carlo Calculations of Selected Dose Components in a Head Model for Boron Neutron Capture Therapy

<abstract xml:lang="en"><title style='display:none'>IEC/EN standards relating to diagnostic radiology equipment, and testing according to these standards</title>The paper gives an outlook of history, present and future of international (IEC) and European (EN) standards relating to diagnostic radiology equipment. These standards may be safety, quality assurance or performance standards; all of them include testing methods. Elaboration and publication of a new series of safety standards is in progress.Acceptance and conformance testing activity of the accredited Radiohygiene Department Laboratory of NRIRR according to these standards is reported.</abstract>

National Research Institute for Radiobiology and Radiohygiene (NRIRR), Budapest, Hungary

IEC & CENELEC TC62 Hungarian National Committee, Budapest, Hungary

IEC/EN standards relating to diagnostic radiology equipment, and testing according to these standards

<abstract xml:lang="en"><title style='display:none'>The design of an insulin pump - preliminary requirements (a technical note)</title>The material presented in this paper is an attempt to lay down requirements for the planned design of an insulin pump. An insulin pump is a device for continuous dosage of insulin at a selected rate, which facilitates treatment and improves the lives of diabetic patients. This paper is a compilation of medical requirements and user suggestions of presently offered insulin pumps.It seems important to establish proper requirements for a device before starting developing any design for an insulin pump.</abstract>

The design of an insulin pump - preliminary requirements (a technical note)

<abstract xml:lang="en"><title style='display:none'>Electron beam characteristics at extended source to surface distance for a Clinac-DHX linear accelerator</title>A uniform dose to the target site is required with a knowledge of delivered dose, central axis depth dose and beam flatness for successful electron treatment at an extended source to surface distance (SSD). In an extended SSD treatment under dosage of the lateral tissue may occur due to reduced beam flatness. To study the changes in beam characteristics, the depth dose curves, beam flatness and isodose distributions were measured at different SSDs from 100 to 120 cm for clinically used field sizes from (4×4) to (25×25) cm2 and beam energies ranging from 6 MeV to 20 MeV. Our results suggest that the change in depth dose is minimal except in the buildup region for most energy. In general surface dose is decreased as the SSD increased moderately. It was observed that the loss in beam flatness is significant for smaller fields, higher isodose lines, and lower energies. The penumbra enlarged and the uniformity index reduced with increasing SSD.</abstract>

Electron beam characteristics at extended source to surface distance for a Clinac-DHX linear accelerator

<abstract xml:lang="en"><title style='display:none'>A Simple Method of Determining the Effective Attenuation Coefficient</title>This paper presents a simple method of determining the effective attenuation coefficient from steady-state diffuse reflectance measurements.</abstract>

A Simple Method of Determining the Effective Attenuation Coefficient

<abstract xml:lang="en"><title style='display:none'>Estimating mental fatigue based on electroencephalogram and heart rate variability</title>The effects of long term mental arithmetic task on psychology are investigated by subjective self-reporting measures and action performance test. Based on electroencephalogram (EEG) and heart rate variability (HRV), the impacts of prolonged cognitive activity on central nervous system and autonomic nervous system are observed and analyzed. Wavelet packet parameters of EEG and power spectral indices of HRV are combined to estimate the change of mental fatigue. Then wavelet packet parameters of EEG which change significantly are extracted as the features of brain activity in different mental fatigue state, support vector machine (SVM) algorithm is applied to differentiate two mental fatigue states. The experimental results show that long term mental arithmetic task induces the mental fatigue. The wavelet packet parameters of EEG and power spectral indices of HRV are strongly correlated with mental fatigue. The predominant activity of autonomic nervous system of subjects turns to the sympathetic activity from parasympathetic activity after the task. Moreover, the slow waves of EEG increase, the fast waves of EEG and the degree of disorder of brain decrease compared with the pre-task. The SVM algorithm can effectively differentiate two mental fatigue states, which achieves the maximum classification accuracy (91%). The SVM algorithm could be a promising tool for the evaluation of mental fatigue.Fatigue, especially mental fatigue, is a common phenomenon in modern life, is a persistent occupational hazard for professional. Mental fatigue is usually accompanied with a sense of weariness, reduced alertness, and reduced mental performance, which would lead the accidents in life, decrease productivity in workplace and harm the health. Therefore, the evaluation of mental fatigue is important for the occupational risk protection, productivity, and occupational health.</abstract>

Estimating mental fatigue based on electroencephalogram and heart rate variability

<abstract>
<title style='display:none'>Abstract</title>
<italic>Introduction:</italic> Squamous cell carcinoma of the head and neck region (HNSCC), with a positive status for high oncogenic potential human papillomavirus (HR-HPV), represents a clinically distinct disease entity compared to HPV-independent cases. Patients exhibit variations in prognosis and proposed therapy regimens. A prompt and reliable diagnosis of the presence of HPV infection could optimize the treatment for these patients. Currently employed treatment methods are long-term, expensive, and lack specificity, especially when administered separately.
<italic>Material and methods:</italic> The research objective of this study is to explore significant differences in the Raman spectra of biological samples taken from patients with HNSCC, facilitating the confirmation of HPV virus presence. Study groups were delineated based on histopathological diagnosis and molecular biology tests, confirming the biological activity of the virus and the presence of the HR-HPV form with a diagnosis of a specific subtype.
<italic>Results:</italic> To identify high oncogenic potential human papillomavirus (HR-HPV) infection as a crucial factor in squamous cell carcinoma of the head and neck region, an effective automatic data analysis system was established, relying on Raman microspectroscopy and multivariate analysis. Our results showed clear ranges of the Raman spectrum that differentiated between HPV-associated and non-HPV-associated cancers.
<italic>Conclusions:</italic> In conclusion, our experience shows a great diagnostic potential of Raman confocal microscopy with multidimensional statistical analysis. In the future, the use of this method may allow for the creation of an effective and automated HR-HPV detection system in neoplastic tissue.
</abstract>

Evaluation of changes caused by HR-HPV infection in squamous cell carcinoma of the head and neck using Raman microspectroscopy in combination with multivariate statistical analysis

<abstract>
<title style='display:none'>Abstract</title>
<italic>Introduction:</italic> Radiochromic film (RCF) is suitable for use as a dosimeter owing to its inherently superior spatial resolution and near-water equivalence. A new model of RCF recommended for measuring imaging dose in the kV nominal energy range was recently introduced onto the market. In this study, we investigate the dependence on the beam quality of GafChromic LD-V1 film’s radiation dose response.
<italic>Material and methods:</italic> Pieces of LD-V1 film were irradiated to air kerma ranging from 0 to 570 mGy in X-ray photons with beam qualities of 60 kV (HVL = 1.32 mm Al), 100 kV (HVL = 2.83 mm Al), 120 kV (HVL = 5.11 mm Al), 150 kV (HVL = 6.23 mm Al), and 180 kV (HVL = 0.54 mm Cu). The net reflectance from each film was obtained from a color flatbed scanner. For each beam quality, an analytical power function was fitted to the net reflectance - air kerma relationship and tested for differences.
<italic>Results:</italic> We have found that for the beam qualities investigated, the response of the Gafchromic LD-V1 film was not significantly dependent on energy, and a single calibration curve could be used. The total relative uncertainty and absolute error reached maxima of 18% and 80%, respectively for air kerma values less than 50 mGy, and remained below 10% for air kerma in the range 50 mGy to 570 mGy.
<italic>Conclusions:</italic> The results of our investigation revealed that the response of Gafchromic LD-V1 film is not significantly dependent on beam quality. A minimum air kerma irradiation of 50 mGy is recommended to minimise uncertainty.
</abstract>

Energy dependence of GafChromic LD-V1 film dose response to X-ray photons in the 60 to 180 kV range

<abstract>
<title style='display:none'>Abstract</title>
<italic>Introduction:</italic> The perfusion of a part of the lung depends on its distance from the pulmonary trunk (differences in vascular resistance) and on the horizontal plane (differences in hydrostatic pressure). The aim of this study was to determine the geometric parameters characterising their positions and sizes in order to analyse the diffusion of the ventilation/perfusion ratio.
<italic>Material and methods:</italic> A developed virtual respiratory system has been supplemented with an appropriate model of pulmonary circulation that uses a lung outline that is divided into parts based on an anatomical atlas and a CT image; it comprises a 3D geometric model of the lungs that was developed using the Inventor CAD software (Autodesk, Inc, San Francisco, USA). Each panel was divided into 2 horizontal and 8 vertical parts; the 16-part division was then modified.
<italic>Results:</italic> When taking human lungs as a research object and simulating their accompanying physical, biological, or biochemical phenomena, one necessary task is to construct a spatial model of the lungs that takes into account, and maintains awareness of, the limitations of the source of data that is relied upon. The developed modified geometric model of lung division turned out to be useful and was successfully applied to a virtual patient, among others, as part of the VirRespir project.
<italic>Conclusions:</italic> Finally, we can conclude that the virtual cardiorespiratory system thus elaborated may serve as a proper tool for the preliminary analysis of such complex interactions, considering the elaborated model of the lung’s divisions and its future improvements.
</abstract>

Lung divisions for models of cardiopulmonary interaction – preliminary tests

<abstract><title style='display:none'>Abstract</title>
<italic>Introduction: </italic>The use of X-ray equipment for medical diagnostic radiography procedures has increased due to advances and complexity of radiological procedures. Achieving good image quality while keeping exposure of workers, public and patient exposure to an acceptable level has become a prerequisite for the radiology department in order to comply with best international practices. The aim of this study was to undertake quality control measurement of seven (7) diagnostic radiography equipment in the south of Benin, the first of its kind.
<italic>Material and methods: </italic>Multifunction detector (Piranha) and beam alignment test tool were used to perform quality control tests on seven (7) X-ray units. The method used as well as the interpretation of the results was based on the American Association of Physicists in Medicine (AAPM), United States Food and Drug Administration (FDA), Healing Arts Radiation Protection (HARP), Institute of Physics and Engineering in Medicine (IPEM), International Atomic Energy Agency (IAEA) and Canadian Safety code 35 (S.C 35) recommendations.
<italic>Results: </italic>The quality control results showed that all X-ray equipment investigated were within standard limits for accuracy of exposure time below 10 ms; reproducibility of kVp, exposure time and dose output; specific dose-kVp2 linearity; and specific dose-mAs linearity. Five (5) out of seven (7) diagnostic X-ray machines passed quality control tests such as X-ray beam alignment, exposure time above 10 ms and kVp accuracy. One (1) X-ray machine failed the quality control test of beam filtration at 70 kVp and above.
<italic>Conclusions: </italic>The findings of this study have provided baseline data for other radiology departments to embark on similar QA/QC activities, and also explore options for optimization of patient dose. However, there is a need to extend the study to cover more diagnostic X-ray machines throughout the country. It is anticipated that this would ultimately assist in improving radiation protection and safety during medical diagnostic radiological procedures.
</abstract>

First implementation of quality control procedures on selected X-ray machines in South of Benin

<abstract><title style='display:none'>Abstract</title>
<italic>Introduction: </italic>The brain is harmed by a medical condition known as a stroke when the blood vessels in the brain burst. Symptoms may appear when the brain’s flow of blood and other nutrients is disrupted. The World Health Organization (WHO) claims that stroke is the leading cause of disability and death worldwide. A stroke can be made less severe by detecting its different warning symptoms early. A brain stroke can be quickly diagnosed using computed tomography (CT) images. Time is passing quickly, although experts are studying every brain CT scan. This situation can cause therapy to be delayed and mistakes to be made. As a result, we focused on using an effective transfer learning approach for stroke detection.
<italic>Material and methods: </italic>To improve the detection accuracy, the stroke-affected region of the brain is segmented using the Red Fox optimization algorithm (RFOA). The processed area is then further processed using the Advanced Dragonfly Algorithm. The segmented image extracts include morphological, wavelet features, and grey-level co-occurrence matrix (GLCM). Modified ResNet152V2 is then used to classify the images of Normal and Stroke. We use the Brain Stroke CT Image Dataset to conduct tests using Python for implementation.
<italic>Results</italic>: Per the performance analysis, the proposed approach outperformed the other deep learning algorithms, achieving the best accuracy of 99.25%, sensitivity of 99.65%, F1-score of 99.06%, precision of 99.63%, and specificity of 99.56%.
<italic>Conclusions: </italic>The proposed deep learning-based classification system returns the best possible solution among all input predictive models considering performance criteria and improves the system’s efficacy; hence, it can assist doctors and radiologists in a better way to diagnose Brain Stroke patients.
</abstract>

Modified ResNet152v2: Binary Classification and Hybrid Segmentation of Brain Stroke Using Transfer Learning-Based Approach

<abstract><title style='display:none'>Abstract</title>
<italic>Introduction: </italic>Asymptomatic inflammatory foci resulting from chronic dental infections or the presence of foreign bodies, e.g., in the sinuses, leading to serious local and systemic complications. These conditions, despite the absence of symptoms, are a source of bacterial, toxic, allergic, and neurogenic effects. Despite the developed radiological diagnostics in the form of pantomographic images and cone beam computed tomography (CBCT), thermal imaging is increasingly mentioned as an auxiliary tool in detecting and treating inflammatory foci of the craniofacial region. It is due that thermal imaging can bring indirectly metabolic information about studied tissues and thus allow the detection of early inflammatory lesions yet not invisible on X-ray diagnostics. The purpose of the study was to apply and validate a protocol for identifying asymptomatic inflammatory foci in the maxillofacial area using thermal imaging.
<italic>Material and methods: </italic>Patients referred to the institute were examined for the presence of inflammatory foci. Analysis of radiographs revealed asymptomatic foci in the maxillary sinus, which were associated with the presence of a displaced foreign body. Thermographic examinations were performed using a FLIR T540 thermal imaging camera.
<italic>Results: </italic>The obtained results showed a significant temperature difference between the suspected and opposite sinus. It was also confirmed that after the foreign body was removed from the sinus the temperature showed a dynamic decrease in time.
<italic>Conclusions: </italic>According to the study, thermography has the potential to become an essential diagnostic tool for inflammation of odontogenic origin. It offers non-invasiveness, safety, real-time imaging, painless and completely safe.
</abstract>

The use of thermovision in the detection of asymptomatic facial inflammation – Pilot study

Instructions for Authors

Publication Agreement

About the Journal

Editorial Policy

Guidelines for Reviewers

Publication list 1995-2006

Polish Journal of Medical Physics and Engineering

The Journal of Polish Society of Medical Physics

 Polish Journal of Medical Physics and Engineering (PJMPE) is an official publication of the Polish Society of Medical Physics (established in 1965, member of IOMP and EFOMP). The...

Impact Factor

Five Year Impact Factor

Cite Score

SNIP

MNiSW

Google Scholar h5-index

Google Scholar h5-median

 Polish Journal of Medical Physics and Engineering (PJMPE) is an official publication of the Polish Society of Medical Physics (established...

Polish Journal of Medical Physics and Engineering

The Journal of Polish Society of Medical Physics

Todos los volúmenes y ediciones en esta revista