Simulations of the Influence of the Heat Flux at the Shaft Surface of the Conical Slide Bearing on Its Hydrodynamic Lubrication and Operating Parameters

[1] Czaban, A., Analiza hydrodynamicznego smarowania ferroolejami stożkowego łożyska ślizgowego, Rozprawa dokt., Uniwersytet Morski, Gdynia 2019.Search in Google Scholar

[2] Frycz, M., Wpływ stężenia cząstek magnetycznych w ferro-oleju na parametry przepływowe i eksploatacyjne poprzecznych łożysk ślizgowych, Rozprawa doktorska, Akademia Morska, Gdynia 2018.Search in Google Scholar

[3] Gohar, R., Elastohydrodynamics, Imperial College Press, Singapore 2001.10.1142/p146Search in Google Scholar

[4] Kelley, C. T., Iterative Solution of Systems of Linear and Nonlinear Equations, Society for Industrial and Applied Mathematics, Philadelphia 1995.10.1137/1.9781611970944Search in Google Scholar

[5] Miszczak, A., Analiza hydrodynamicznego smarowania ferrocieczą poprzecznych łożysk ślizgowych, Fundacja Rozwoju Akademii Morskiej, Gdynia 2006.Search in Google Scholar

[6] Wierzcholski, K., Miszczak, A., Mathematical principles and methods of biological surface lubrication with phospholipids bilayers, Biosystems, Vol. 178, pp. 32-40, 2019.10.1016/j.biosystems.2018.11.00230448537Search in Google Scholar

• Analysis of Possibility Limiting the Time of Test Injector in Diesel Engine Using Factory Test Bench Producers of these Elements
• Simulations of the Influence of the Heat Flux at the Shaft Surface of the Conical Slide Bearing on Its Hydrodynamic Lubrication and Operating Parameters
• Slip at Vehicle Transmission System with Hydrokinetic Converter in the Urban Test Cycle
• Mechanical Properties of AW-5083 Alloy Joints Welded By Hybrid Method – FSW and MIG
• Operational Verification of a Ship Main Power System Element Choice – Case Study
• Modelling Method of Dynamic Characteristics of Marine Thin-Walled Structure
• The Influence of Cutting Parameters on Surface Topography During Turning Marine Pump Shafts
• Composite Materials for Warship Constructions
• Distributions of Hydrodynamic Pressure in the Gap of Slide Journal Bearing Lubricated with Ferro-Oil
• Application of Similarity Method of Distance Courses Describing the Elements Content in Cement Concrete After 50 Forced Thermal Cycles
• Comparative Analysis of Fuels Derived from PE Plastic Waste with a Mixture of Plastic Recycling Waste of Codes: 1, 2, 4, 5, 6 and 7 Based on Low-Temperature Pyrolysis
• Operating Parameters of a Slide Bearing with Parabolic-Shaped Slide Surfaces with Consideration of the Stochastic Changes in the Lubrication Gap Height
• Application of Similarity Method of Distance Courses Describing the Elements Content in Typical Cement Concrete After Thermal Cycles
• Solutions in the Vehicle Suspension
• The Experimental Investigation of Surface Roughness After Dry Turning of Steel S235
• Numerical Investigation of Endplates Influence on the Wing in Ground Effect Lift Force
• Effect of the Recyclate on a Deflection of Composites in Bending
• Analysis of Electric Vehicles Efficiency and their Influence on Environmental Pollution
• Energy Balance of a Vehicle Equipped with Hybrid Propulsion System Fuelled with Alternative Fuels
• Using Sorbents for Oil Spill Clean-Up in Ports and Coastal Areas
• Determination of Material Characteristics Necessary for Modelling of Marine Structures Exposed to Small-Calibre Bullet
• Investigation of Thermal Properties of Novel Phase Change Material Mixtures (Octadecane-Diamond) with Laser Flash Analysis
• Technical and Ecological Analysis of Different Solutions of the Power Supply of a Marine Diesel Engine
• Influence of Inlet Geometry on the Efficiency of 1 MW Steam Turbine
• Modelling of Transport System Operational Reliability a Markov Approach
• Analysis of the Vehicle Exploitation Process with Regard to Profiling
• Introduction to the Examination of Thin-Walled Structures Using the Vibrodiagnostic Method
• Anomaly of Rotor Dynamics in Ultra-Light Helicopter – Robinson R22
• Storage of Wind Power Energy
• Numerical Investigations of Stress Concentration in Reinforcement Steel Structure by Composite Overlays
• Modelling of Helicopter Main Rotor Aerodynamic Loads in Manoeuvres
• Analysis of Possibility of Repairing Welding of Selected of the Steam Turbines
• An Influence of Correction of the Ignition Advance Angle on the Combustion Process in SI Engine Fuelled by LPG with the Addition of DME
• Comparative Preliminary Unit Costs Analysis of the Operation of Passenger Cars with Combustion Engines and Fuel Cell Vehicles Powered by Hydrogen
• The Development of the World Fleet of Electric Vehicles in Years 2010–2017 with Emphasis on Fuel-Cell Vehicles
• Validation of Microscopy Measured Porosity in Carbon Fibbers Composites
• Self-Learning Control Algorithms Used to Manage the Operating of an Internal Combustion Engine