Roughness Effects of Textured Surfaces in Hydrodynamic Lubrication

[1] Fowell M., Olver A.V., Gosman A.D., Spikes H.A. and Pegg I. (2007): Entrainment and inlet suction: two mechanisms of hydrodynamic lubrication in textured bearings.– ASME Journal of Tribology, vol.129, pp.336-345.10.1115/1.2540089 Search in Google Scholar

[2] Holmberg K. and Erdemir A. (2017): Influence of tribology on global energy consumption, costs and emissions.– Friction, vol.5, pp.263-284.10.1007/s40544-017-0183-5 Search in Google Scholar

[3] Sudeep U., Tandon N. and Pandey RK. (2015): Performance of lubricated rolling/sliding concentrated contacts with surface textures: a review.– J Tribol-Trans ASME, vol.137, No.3, Article No.031501, p.11, https://doi.org/10.1115/1.4029770. Search in Google Scholar

[4] Gu C.X, Meng X.H, Xie Y.B. and Yang Y.M. (2016): Effects of surface texturing on ring/liner friction under starved lubrication.– Tribology International, vol.94, pp.591-605, https://doi.org/10.1016/j.triboint.2015.10.024. Search in Google Scholar

[5] Ausas R., Ragot P., Leiva J., Jai M., Bayada G. and Buscaglia G.C. (2007): The impact of the cavitation model in the analysis of microtextured lubricated journal bearing.– J Tribol-Trans ASME, vol.129, No.4, pp.868-875, https://doi.org/10.1115/1.2768088. Search in Google Scholar

[6] Jakobsson B. and Floberg L. (1957): The Finite Journal Bearing, Considering Vaporization.– Gumperts Förlag, p.116. Search in Google Scholar

[7] Olsson K.-O. (1965): Cavitation in Dynamically Loaded Bearing.– Scandinavian University Books, p.59. Search in Google Scholar

[8] Gropper D., Wang L. and Harvey T.J. (2016): Hydrodynamic lubrication of textured surfaces: a review of modeling techniques and key finding.– Tribology International, vol.94, pp.509-529, https://doi.org/10.1016/j.triboint.2015.10.009. Search in Google Scholar

[9] Muchammad M., Tauviqirrahman M., Jamari J. and Schipper D.J. (2016): An analytical approach on the tribological behavior of pocketed slider bearings with boundary slip including cavitation.– Lubrication Science, vol.29, No.3, pp.133-152, https://doi.org/10.1002/ls.1361. Search in Google Scholar

[10] El Gadari M., Fatu A. and Hajjam M. (2016): Effect of the grooved shaft on the rotary lip seal performance in transient condition: Elasto-hydrodynamic simulation.– Tribology International, vol.93, Part A, pp.411-418, https://doi.org/10.1016/j.triboint.2015.09.031. Search in Google Scholar

• Two-Dimensional Analysis of Functionally Graded Thermoelastic Microelongated Solid
• Joining of Carbon Steel AISI 1006 to Aluminum Alloy AA6061-T6 Via Friction Spot Joining Technique
• An Investigation of the Suspension Characteristics of the Line Model of the Vehicle Using the Taguchi Method
• Computational Approach to Solving a Layered Behaviour Differential Equation with Large Delay Using Quadrature Scheme
• Generalized Plane Waves in a Rotating Thermoelastic Double Porous Solid
• Visco-Elastic Fluid Model in an Inclined Porous Stenosed Artery with Slip Effect and Body Acceleration
• The Influence of Thermal Expansion on Flow Past an Inclined Accelerated Sectional Plate with Persistent Mass Diffusion
• Applying Optimization Techniques on Cold-Formed C-Channel Section Under Bending
• Heat Transfer Effects on Carbon Nanotubes Along a Moving Flat Plate Subjected to Uniform Heat Flux
• Fabrication of a High Wear Resistance AA7075/AL2O3 Composites Via Liquid Metallurgy Process
• Influence of Form Defect on the Mechanical Behavior and Stress Intensity Factor of Shrink-Fitted Thick-Walled Cylinders
• Optimization of Friction Stir Processing Parameters of Aluminum Alloy Reinforced with Hybrid Nanoparticles Using the Taguchi Method
• A Method for Comparison of Large Deflection in Beams
• Effect of Ultrasonic Peening on Mechanical Properties of Low Carbon Steel AISI 1020 TIG Welding Joints Process
• Strouhal Number Effects on Dynamic Boundary Layer Evolution Over a Wedge Surface from Initial Flow to Steady Flow: Analytical Approach